Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

Why are we measuring gel content of NBR latex? Does gel content related to the amount of cross-linked in a polymer?

Hi good day to everyone! I am actually studying the gel content of synthetic latex. Refer to ASTM 3616, gel content is measure of insoluble rubbers in the chosen solvent. So, I just would like to...

07 February 2021 605 4 View

How to delete a copy of a paper, and how to delete a co-author's name?

I mistakenly uploaded a copy of the same paper and entered my alternative name. How to delete them out? (I couldn't navigate to the right buttons to do it. So from where to where is what I don't...

07 January 2021 7,694 6 View

What effect will different solvents have on the ATRP reaction?

I want to do an ATRP reaction, synthesize an ATRP initiator, use DMF as a solvent, and mix DMF, BIBB and TEA to turn red. Why does it turn red? Xylene has been used as a solvent before, and there...

04 January 2021 8,034 3 View

Species identification.Who can tell me the scientific names of these Gastropods?

Species identification. I've been doing research on communities of marine macrobenthos recently, but some of them can't be identified, which hinders my research. Who can help me identify these...

14 December 2020 8,357 3 View

Cell shrinkage during ROS assay(H2DCFDA)?

Hi! I'm Yu, studying about health of MSC. These days, I'm doing ROS assay with H2DCFDA which requires 5~30 minutes of staining with PBS or HEPES or HBSS. In our lab, We use PBS w/o Mg/Ca for...

13 December 2020 8,813 9 View

Can I fix the cells after H2DCFDA assay for FACS analysis?

Hi ! I'm Yu, and planning to analyze ROS assay with H2DCFDA(Thermo) on MSCs. A lot of protocols instruct that treat H2DCFDA at specific concentration for 5~30 min, 20~30 min of recovery time...

10 December 2020 973 1 View

How to reconstruct a Lamb wave by a series of pulses superposed?

Lamb wave is useful for solid structure health monitoring, and it consists many modes. Unlike ultrasonic bulk wave, when given a pulse excitation (for example, 5-cycle sinusoidal pulse), only...

08 December 2020 5,440 8 View

How to interpret the significant effect of covariates when conducting a Two-way ANCOVA?

06 December 2020 8,560 4 View

Did anyone do microglia Oil Red O staining?

I need to stain adiposome in microglia, but I don't know how to confirm that are really success? method : Removed media and washed cells with PBS, then added 4 % paraformaldehyde for 20 minutes at...

24 November 2020 2,359 2 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

Color of spiro-ometad film?

What does the color of a spiro-ometad film indicate? I got purple, green, red, even black color of the spiro film. Is there anything we can get from the preliminary color analysis(e.g. oxidation...

21 February 2021 1,831 4 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View