Why in METRIC and SEBAL, surface temperature is used in the Monin-Oubukhov length equation?

HAMIMED Abderrahmane @HAMIMED_Abderrahmane

12 December 2018 0 400 Report

Why in the surface energy balance modeling with METRIC and SEBAL, surface temperature (Ts) is used in the Monin-Oubukhov's length equation instead of air temperature (Ta)?

Badges
Science topic

Similar topics
Engineering
Modeling

More HAMIMED Abderrahmane's questions See All

How to derive soil water holding capacity from remotely sensed infrared data?

Is it possible to use remote sensing visible and thermal infrared image combined with surface modeling for estimating soil water holding capacity?

08 September 2018 6,031 1 View

On the use of LST-NDVI trapezoid relationship for possible estimating kB-1 and roughness length for heat transport ?

Brutsaert (in his book "Evaporation into the atmosphere: theory, history and applications") showed that the value of kB-1 can range from 2 for total cover crops to a wet soil at 8.5 for a dry and...

08 September 2018 9,401 7 View

Application de STICS en Algérie?

Est-il possible d'appliquer le modèle STICS dans les conditions semi-arides algériennes dans le cadre d'une collaboration.

01 January 1970 2,028 7 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to develop investments in renewable energy sources?

08 August 2024 5,112 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View