Why does not the dynamic mesh work with wind turbines, no rotation?

Ahmed S. Mansour @Ahmed_Mansour55

04 April 2018 1 5K Report

Anybody carry out a simulation using the dynamic mesh in Fluent for turbines?

Thanks

Ahmed S. Mansour

Thanks

Badges
Science topic

More Ahmed S. Mansour's questions See All

How do we correctly setup the solar ray tracing for a Photo Voltaic PV panel simulation in ANSYS FLUENT?

Hello, I have a simple model (PV cell+ air channel) and I do not know how to let the sun rays hit the PV surface and then transfer the heat to the air..What I see is the sun rays hit the air...

08 September 2019 475 2 View

What are the equations of the boundary layer of a flat plate that TDMA method is based on?

Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...

05 June 2019 7,941 4 View

How to define a heat flux and convection coefficient at the same time on a wall using user defined function in FLUENT?

Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!

05 June 2019 7,041 12 View

How can we define a symmetry wall boundary condition in Fluent?

Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...

04 May 2019 5,819 3 View

How to use Chemkin to model the model studied in the attached paper?

Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks

04 May 2019 3,934 2 View

Can we cople between ANSYS FLUENT and Simplorer ASAP?

Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!

03 April 2019 2,674 6 View

How can we define a heat flux boundary condition + convection for one wall in ANSYS FLUENT?

Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks

02 March 2019 5,946 4 View

What are the equations used to simulate a steady state thermal analysis using FEA ANSYS thermal?

Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks

31 December 2018 5,790 5 View

How can we save calculations to a text file from a Matlab CFD code during running the code like ANSYS FLUENT?

Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!

31 December 2018 816 3 View

How to save data in a file from MATLAB GUI?

Hello, we have a MATLAB GUI code and it produces a graph, we need to save the data of the graph in a txt file, how can we do it? Thanks

09 October 2018 6,552 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View