Why does my EML block giving error-index expression out of bounds in Simulink?

Alok Jain @Alok_Jain9

09 September 2016 0 9K Report

I have written code in Embedded MATLAB Simulink Block. But i am getting this error-

Index expression out of bounds. Attempted to access element 2. The valid range is 1-1.

What does it mean?? and please help me in removing this error.

i have also attached image of this error list.

Badges
Science topic

More Alok Jain's questions See All

I want single phase Voltage and current graph from the three phase current and voltage graph in matlab simulink?

In my simulink model, i am getting from scope three phase voltage signal, but i need graph of individual phase graph? How can i get the individual phase graphs?

07 August 2018 9,756 3 View

What is the typical value of impedance for 0.5ohm/km line in ac distributor?

I want the typical value of impedance for 0.5ohm/km line in ac distributor? can i get any reference of this whr it is used

03 April 2018 7,552 0 View

While loading simulink model in OPAL-RT lab getting Error- Some of the parameters are not double?

OPAL-RT Error- Some of the parameters are not double? Editin eMEGASIM- After building my simulink model in OPAL-RT, at the time of loading of the model then I am getting one error- 017-4-11...

03 April 2017 9,398 1 View

Help regarding SIMULINK model of PMU

I want to make simulink model of PMU- PHASOR MEASUREMENT UNIT. I have attached paper in which PMU simulink model is given. Plz have a look and help me in making PMU simulink Diagram.

07 August 2016 6,783 1 View

Is anyone have the knowledge of LABVIEW software?

As i am working on LABVIEW and i am getting some problem in it. Basically I have to estimate the phasors of any sinusoidal signal through recursive and non-recursive DFT algorithm. I have made 1...

07 August 2016 2,271 6 View

Is anybody have the Idea of LABVIEW software ?

As i am working on LABVIEW and i am getting some error problem in it. Basically I have to estimate the phasors of any sinusoidal signal through recursive and non-recursive DFT algorithm. I have...

06 July 2016 8,858 1 View

How to write (Costheta-jsin*theta) in Labview?

As I am working on Labview software and i have to write (Cos*theta-j*sin*theta)=e-j*theta, where theta= 2*pi/N, N=no of samples=12, in Labview. But, for this i didnt get any block in lib So,...

06 July 2016 3,746 9 View

From where can I get the simulink model of PMU- Phase Measurement Unit?

As i want to add the simulink model of PMU to my simulation but From where I can get the PMU simulink model?or from and how I construct the simulink model of PMU in MATLAB?

11 December 2015 6,284 26 View

How smart meters help in mitigating power quality problems???

for example if i have to mitigate Voltage sag in distribution line through smart meter?? Let voltage sag is there in the distribution line, first of all it is sensed by the Smart meter and then...

09 October 2015 5,616 4 View

OPAL-RT Error- Some of the parameters are not double?

in eMEGASIM- After building my simulink model in OPAL-RT, at the time of loading of the model then I am getting one error- 017-4-11 20h24m23s:You should add an OpSync block if you want to...

01 January 1970 5,691 0 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Can we mark 'EFL Learners shifting from general digital to AI technologies' as technological transition?

After COVID-19 it has seen that EFL learners technological affiliation has raised. In addition, in the post-COVID period learners started to engage AI technologies like ChatGPT while learning...

08 August 2024 8,964 4 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View