How to write (Cos*theta-j*sin*theta) in Labview?

More Alok Jain's questions See All

I want single phase Voltage and current graph from the three phase current and voltage graph in matlab simulink?

In my simulink model, i am getting from scope three phase voltage signal, but i need graph of individual phase graph? How can i get the individual phase graphs?

07 August 2018 9,756 3 View

What is the typical value of impedance for 0.5ohm/km line in ac distributor?

I want the typical value of impedance for 0.5ohm/km line in ac distributor? can i get any reference of this whr it is used

03 April 2018 7,552 0 View

While loading simulink model in OPAL-RT lab getting Error- Some of the parameters are not double?

OPAL-RT Error- Some of the parameters are not double? Editin eMEGASIM- After building my simulink model in OPAL-RT, at the time of loading of the model then I am getting one error- 017-4-11...

03 April 2017 9,398 1 View

Why does my EML block giving error-index expression out of bounds in Simulink?

I have written code in Embedded MATLAB Simulink Block. But i am getting this error- Index expression out of bounds. Attempted to access element 2. The valid range is 1-1. What does it mean?? and...

08 September 2016 8,836 0 View

Help regarding SIMULINK model of PMU

I want to make simulink model of PMU- PHASOR MEASUREMENT UNIT. I have attached paper in which PMU simulink model is given. Plz have a look and help me in making PMU simulink Diagram.

07 August 2016 6,783 1 View

Is anyone have the knowledge of LABVIEW software?

As i am working on LABVIEW and i am getting some problem in it. Basically I have to estimate the phasors of any sinusoidal signal through recursive and non-recursive DFT algorithm. I have made 1...

07 August 2016 2,271 6 View

Is anybody have the Idea of LABVIEW software ?

As i am working on LABVIEW and i am getting some error problem in it. Basically I have to estimate the phasors of any sinusoidal signal through recursive and non-recursive DFT algorithm. I have...

06 July 2016 8,858 1 View

From where can I get the simulink model of PMU- Phase Measurement Unit?

As i want to add the simulink model of PMU to my simulation but From where I can get the PMU simulink model?or from and how I construct the simulink model of PMU in MATLAB?

11 December 2015 6,284 26 View

How smart meters help in mitigating power quality problems???

for example if i have to mitigate Voltage sag in distribution line through smart meter?? Let voltage sag is there in the distribution line, first of all it is sensed by the Smart meter and then...

09 October 2015 5,616 4 View

OPAL-RT Error- Some of the parameters are not double?

in eMEGASIM- After building my simulink model in OPAL-RT, at the time of loading of the model then I am getting one error- 017-4-11 20h24m23s:You should add an OpSync block if you want to...

01 January 1970 5,691 0 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

How to conduct a sensitivity power analysis for Kendall's Tau?

Is there a straightforward way to conduct a sensitivity power analysis for a Kendall's Tau correlation? I was considering using the sensitivity setting and "Correlation: point biserial model" test...

28 July 2024 6,133 8 View

Terrorism, a natural inclination of all animal species?

There are many types of symbolic judgements. For example, when an Israeli pilot flattens the home of a Palestinian family (even if they are forewarned), it is natural for them to experience shock...

28 July 2024 2,610 1 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Gustav Karl Henrik Wiberg

I guess this is what you are looking for. You forgot to mention that theta is an array, else it makes not any sense.

Alok Jain

Sir plz send me VI file.

here you go

try 2

Sir i am getting NAN ERROR. PLZ SEE MY vi.

FILE

it looks like I cannot attached the file. I've sent it privately though a message.

yes sir. there is no file. See this file.

See the .png image of thew model