What softwares are helpful for analysing optical properties of nanomaterials?

Please give details of the software

04 May 2017 2,073 0 View

What softwares are helpful for analysing optical properties of nanomaterials?

i want details of the software

04 May 2017 2,598 4 View

Please suggest some new material for my future research project? I want to work in nanomaterials in material science department.

It ll be helpful to concentrate for future projects...i want material that will be important for next decade

03 April 2017 5,321 9 View

Why there are differences in calculation of Refractive Index of nanomaterial , when calculated from 2 route, from reflactance and transmittance data?

please give theoretical analysis

03 April 2017 717 2 View

What ligand we should used to bind CNT and iron oxides or vice-versa?

I want to get CNT/Iron Oxide thin film layer by chemical process.

09 October 2016 7,356 2 View

Why metal sulphides thin film acts as a gas sensor??

i want a model or theory related to this

08 September 2015 8,765 2 View

What should be the GOF in maud analysis? I cannot fit the curve for sigma less than 2.2. Is my fitting not appropiate??

Please tell me the valid range for GOF and also i want to know why it varies

09 October 2014 7,998 0 View

What is the basic principle of CdS thin film gas sensing property against H2S and LPG gases?

I want chemical reaction also.....

07 August 2014 9,625 1 View

What is the basic principle of CdS thin film gas sensing property against H2S and LPG gases?

Give me the chemical reaction

07 August 2014 8,697 2 View

How can the sensitivity of metal sulphides be increased by doping?

please give the basic chemical reaction of it

07 August 2014 1,641 2 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

How do I calculate absorption coefficient of my thin film if I dont know the thickness? Or how can I calculate the thickness of my sample?

I have done Uv-vis characterisation of my thin film and have received absorbance and transmittance data. Now I want to calculate the absorption coefficient but I dont know the thickness of my...

21 February 2021 7,148 8 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View