Why do ABS polymers, or maybe others, show higher tensile modulus than tensile strength?

15 January 2015 1 4K Report

ABS shows tensile modulus around 2000 MPa where as tensile strength around 45 MPa. Modulus is much more higher than strength. What does it define exactly?

Hemjyoti Kalita

Thanks

Badges
Science topic

More Hemjyoti Kalita's questions See All

How to check leakage current of Si-SiO2 wafer?

I want to use the n-type Si wafer coated with a 300 nm SiO2 layer for the OFET device, but for that, I have to check the leakage current of the dielectric layer. how?

07 February 2024 4,115 2 View

What will be the quality of Al2O3 layer in OFET device fabricated through RF Sputtering?

This question is related to OFET devices. Please suggest some answers to this question.

07 February 2024 8,067 0 View

How to extract velocity data of a moving object from a simulation done in Ansys Fluent?

Hello Everyone!! I am currently working on a model for renewable energy harvesting using ocean wave energy in Ansys fluent. I have applied a dynamic mesh and compiled the UDF for motion of a...

30 January 2024 8,896 1 View

How to remove negative volume error in Ansys fluent dynamic mesh?

Hello Everyone!! I am currently working on a model for renewable energy harvesting using ocean wave energy in Ansys fluent. I have a design ready along with a UDF for a moving component. But when...

08 October 2023 5,531 5 View

How can we isolate exopolysaccharide content from cyanobacterial strains?

Is there any method for isolating exopolysaccharides (not the total Carbohydrate) from cyanobacteria?

06 August 2023 4,234 2 View

How can I find or estimate the species specific parameters α and β for application in Beta-poisson model for QMRA?

I am trying to estimate the QMRA for three species of bacteria using beta-poisson model. The literatures that I followed have not reported the α and β values for these 3 specific bacteria, while α...

27 May 2023 5,692 0 View

Q-Exactive calibration error for Mass resolution Dependency too high, can anyone help?

Hi, After performing my annual cleaning on the QE and calibrated, it as passes the positive cal but when performing the basic (negative) Analyzer accuracy it has failed for Mass resolution...

08 January 2023 2,206 1 View

What is the simplest method for hematocrit correction during glucose measurement in electrochemical dry strip technology?

Hematocrit correction during glucose measurement is very important for enhancing the accuracy of measurement in whole blood. As far my knowledge, it done electrochemically either through impedance...

20 December 2022 8,534 0 View

How to distinguish triplet-triplet annihilation band from phosphorescence and TADF?

If an organic molecular emitter shows multiple photoluminescence bands, what tools and techniques can one use to confirm the triplet-triplet annihilation (TTA) band?

18 November 2022 6,879 4 View

Can anyone tell me how to publish RFC standard?

I want to publish a work as an enhanced version of RFC 8180.

11 November 2022 6,235 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Can anyone explain why there is not any color bands in the middle portion of the tensile coupon?

Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)

03 August 2024 8,538 4 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

A twin-shaft kiln or a rotary kiln for lime production 1 class? if compressive strength of limestone is low 60 MPa?

My research work is related to the calcination of limestone. I have a complex question and would like to consult with experts in this field. Could you please advise which kiln to choose (a...

18 July 2024 1,390 2 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View