Why brine has is stronger cooling media than pure water?

01 January 2017 0 6K Report

effect of salt or sugar addition to water on the cooling performance of the solution

Badges
Science topic

Similar topics
Social Science
Media

More Ahmed Taifor's questions See All

Why does the applied force in a model can't be exported from ansys workbench to abaqus?

I have exported a model with all boundary condition and meshes from ansys workbench to abaqus. the imported model has the same meshes and fixed boundary as in the ansys but the applied force did...

31 December 2018 9,037 0 View

I want to improve the strength of adhesive using nano particles how can I increase the wetting?

What chemicals should I use to increase the wettability of nanoparticles the nano are carbon tubes, alumina, silica. The adhesives are wooden glue and epoxy.

11 December 2018 3,617 0 View

Hi, I want to use taguchi method with 5 factors 4 levels but with some missing levels ?

Dears, I want to conduct a research about composite materials. in my work I have 5 parameters with 4 levels but the problem is that some of the parameters have only two or three levels (see table...

11 December 2018 5,042 5 View

Can we use hotspot stress method to caculate stress in SHS T joints in which two gamma beyond the allowable limit to find stress concentration factor?

Using hot spot stress to calculate the stress concentration factor require that 2 gamma which is the chord width to thickness ratio in square hollow sections/ t- joint welds to be greater than 12...

10 November 2018 3,562 1 View

Why do I get abnormal results in mechanical ansys workbench?

Hi, I am simulating the effect of design parameters on welded joints. Despite that, I applied only 1KN.m bending moment on the model but the out put Von Mises stress values are abnormal and of...

08 September 2018 1,922 10 View

abnormal von mises values in mechanical workbench?

despite that, I have tried many methods to solve the issue of abnormal stress values around weld joints but all didn't work. why? I applied 100 KN lateral force at the top and fixed the model from...

08 September 2018 464 0 View

Why this warning " the maximum contact stiffness is too big" appears in workbench?

1. what is the reason of the aforementioned warning? 2. how can I solve the problem? 3. what is the effect on the results? hint: I am working on welded joint under fatigue load using mechanical...

08 September 2018 4,416 3 View

How can I show the results on all nodes in the model of workbench?

Dears, I would like to show the principle stress of all nodes in my model using workbench directly without exporting to excel sheet. how can I do it?

08 September 2018 8,651 0 View

Simulation of hyperelastic materials using Ansys workbench ?

Hi, using stress strain data of uniaxial tensile test, I fitted the curve using Mooney- Rivilin 5 parameters method of hyperelastic materials. But when I run the program a warning message appears...

05 June 2018 7,995 0 View

Why I can't simulate with hyper elastic materials?

hi, I'm investigating the effect of impact on the mobile cover which is made of hyperelastic rubber using explicit dynamic workbench. The curve of tensile test was fitted using 5 parameters...

04 May 2018 3,671 3 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

Could any one guide me, to write research proposal for grant? ?

We have one plant, the local people using this for controlling blood sugar, the toxicity and antidiabetic activity of the plant is not reported yet, please guide from whag should be the process ?...

02 March 2021 2,300 1 View

How can we obtain a modification factor for creep parameters?

I want to obtain standard creep parameters of salt rock by creep parameters of rectangular samples. Is there a modification factor to convert creep parameters of rectangular (prismatic) rock salt...

01 March 2021 7,131 1 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

Precipitate after adding laemmli buffer to protein solution containing Potassium Acetate?

Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...

01 March 2021 2,622 3 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Which transition metal salt precursor is best for doping? Why?

I would like to synthesize a transition metal doped TiO2 via solgel method. Hence, I would like to know which metal salt precursor to choose among Chloride, Nitrate, and Sulphate. A clear...

27 February 2021 4,285 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

How can I set up a good fit SEM model in AMOS?

I am trying to make an SEM model in AMOS for my dissertation but having some trouble with getting a good fit. I am looking for relationships between self-efficacy reported on a Likert scale and...

26 February 2021 8,642 4 View

What are the saturated salt solutions that can give specific relative humidity of 35%, 65% and 95% for conditioning wood specimens?

Due to the unavailability of climate rooms, I want to carry out an experiment that require the use of certain saturated salt solutions especially those that can condition the wood specimen to 35%,...

25 February 2021 8,139 1 View