07 July 2016 1 5K Report

His paper shows impressive "fluency" in the philosophy of modeling:

MATHEMATICAL MODELS IN BIOLOGICAL THEORY

J. A. RAFFERTY

American Scientist

Vol. 38, No. 4 (OCTOBER 1950), pp. 549-567, 579

More Karlis Podnieks's questions See All
What is known about frequency or wave-length of oscillations of Sn(x)?

The question is asked on p.809 of Feller's 1945 paper THE FUNDAMENTAL LIMIT THEOREMS IN PROBABILITY, see...

05 June 2016 6,106 3 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal?

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice

04 August 2024 7,367 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close