Who can tell me how to employ an Endogenous-Switching Poisson regression model ?

More Cishahayo Laurent's questions See All

DdPCR analysis: biological replicates ?

--Hi, such as RTqPCR to analyse gene expression, is it necessary to have biological replicates in a ddPCR experiment ? thank yu --

21 May 2024 8,181 6 View

Model for reconstructing the number of inhabitants from the number of burials ?

hi, I'm trying to find out if there are any models for the medieval period south of the Sahara in West Africa that can be used to reconstitute the number of inhabitants at a site from the number...

04 November 2023 2,666 1 View

Aerosol biocontamination and sanitation network ?

Good morning, I am looking for publications/data regarding aerosol biocontamination from the sanitation network lift stations. Would you be aware of any articles or complications on this...

17 July 2023 2,369 0 View

Freeze Drying small volumes : What should be considered ?

Hi All, we usually discuss different tips in order to freeze dry large volume samples (e.g. two steps freezing, etc). I would like to ask you if you have any tips regarding the small volumes ? For...

20 June 2023 4,324 2 View

What do we know about the costs of synthetic fuels in road transport?

From 2035 on, besides fully electric cars, the EU will also allow the putting on the market of cars powered by synthetic fuels/e-fuels. Do you know an up-to-date, reliable independent estimate of...

29 March 2023 9,160 2 View

What is the significance difference between a p-value of 0.01 and a p-value of 0.012 ?

--Hi, p-value = 0.01 and p-value = 0.012 is it risky to say that it is the same thing in terms of probability ? p=0.01 --> * * p=0.012 (p>0.01) --> * Thank you --

09 November 2022 7,448 3 View

How to sample blood on X. laevis ?

Hi everyone, I am currently working with X. laevis and I would like to collect blood samples. This would happened right before euthanasia on anesthetized individuals. My aim is to measure...

20 June 2022 8,691 0 View

Could you recommend a method or pipeline for quality control and paralog removal from amplicon sequencing data?

Hello everyone, I have recently started working with NGS data (amplicon sequencing) for phylogenetics and species-delimitation studies of closely-related specimens (typically within a genus or a...

02 April 2022 3,139 0 View

Are changes significant?

Dear everyone, I've seen many posts in this community that seem to answer my questions but I have a tough time figuring out how my situation compares to the one described by the op's and I'm...

24 December 2021 7,852 4 View

What do we know about the behavioural reactions to the announcement of forthcoming low emission zones/diesel bans/ICE bans?

So I not referring to ex post adaptation, but to what happens between the time when the policy was announced and/ the time it entered into force. How quickly did such announcements affect fleet...

28 July 2021 3,190 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Is there an alternative to a multinomial regression which allows the DV to be non mutually exclusive?

I am trying to analyse data from a survey examining what variables affect teachers perceived barriers to incorporating technology into their classroom. I have 5 predictor variables however my DV...

06 August 2024 1,752 3 View

In order to run Multinomial Logistic Regression, is it required that the data be in the long format?

I am using unit level data (IHDS round 2) & Stata 17

06 August 2024 5,725 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Abolfazl Ghoodjani

Hello Cishahayo Laurent Simply start with the example of GraphPad Prism software in Poisson regression.

The software does all the analysis and placement for you automatically.

A good and excellent software with a variety of practical examples

Mohammed Jasim Mohammed

Dear Cishahayo Laurent you can use R software

https://cran.r-project.org/web/packages/pscl/vignettes/countreg.pdf