Which tools are used for multistage interconnection network model implementation?

12 August 2017 0 282 Report

Which tool is used to implement routing algorithm in multistage interconnection network?

Badges
Science topic

Similar topics
Filing

More Sonam Seth's questions See All

How to form the state space model of SMIB with Power Electronic Load?

I am working on a small signal stability analysis of a power system on a power electronic load. The power electronic load is modeled as a voltage-dependent load and has the relation attached in...

26 June 2024 2,496 1 View

How can we model Power Electronic Load for carrying out small signal stability analysis?

Currently, I am working on modeling power electronic loads to perform small signal stability analysis. Anyone researching the same area can help me, as there is limited literature on this area. Or...

16 May 2024 5,468 2 View

Any thoughts on troubleshooting my CC9 KO experiment?

Hi, I'm currently trying to generate a one-vector plasmid system for a knockout using CRISPR/Cas9. I'm using lentiCRISPRv2 (ampicillin-resistant) and following the GeCKO Target Guide Sequence...

29 April 2024 3,660 0 View

What is the Impact of empowering an inquiring mind in a classroom?

History of what lead to this thinking Current issues and debates around this paradigm

01 April 2024 459 0 View

Why oscillation frequency less than 1 Hz is termed as inter-area mode and frequency between 1 -2 Hz is termed as local mode of oscillation?

mode of oscillation is classified as stated in the question. I would be grateful if someone can share the literature about it.

17 March 2024 1,846 2 View

How can I measure signal intensity of Hoffa's fat pad?

I want to examine the correlation between signal intensity of Hoffa's fat pad and KL grades of knee osteoarthritis. But i am not able to get how to measure the signal intensity. Elliptical/round...

11 March 2024 9,693 1 View

Respected members! Can someone please suggest me radiology related topics to write a review article?

If any respected member want to share the work with me.. i am ready.

20 February 2024 4,189 8 View

Oscillation frequency of induction motor load in power system stability studies?

Hi, I am carrying out a small signal stability analysis of a power system with an induction motor (squirrel cage) as the load. I am interested in investigating the frequency of oscillation and...

11 February 2024 3,583 0 View

Why number of states does not get reduced when power system stabilizer is deleted from the Model developed in MATLAB/Simulink?

I am working on the small-signal stability of the SMIB system. I want to find the oscillation frequency and damping ratio without and with the power system stabilizer. When I removed the PSS from...

07 February 2024 1,401 0 View

How to separate symetrical diselenide and selenide from a reaction mixture?

I want to get pure diselenide substrate but in the rxn mixture both selenides and diselenides are forming. and both have the same retaintion factor value. so, I am not able to separate it through...

20 October 2023 898 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View