Which solvent is best to dispersion ZnO and TiO2 nanoparticles for anti corrosion mild steel research ??

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

Can i quantify a nanoparticle encapsulated in cell culture medium by hplc?

Hello, if you made a transwell assay where you incubate the cells with a nanoparticle-encapsulated drug and considering that in the oposite compartment you'll have both the free and encapsulte...

03 August 2024 2,730 1 View

Mossbauer spectroscopy Co0.6Mn0.4Fe2O4 MNPs?

Following curve related to Co0.6Mn0.4Fe2O4 Magnetic nanoparticles with extra phase a-Fe2O3. I will appreciate to help me to interpretation this spectroscopy, especially the blue line.

31 July 2024 9,140 2 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

I have synthesized a composite of ZnO and In2O3 with variations in ZnO content. In Raman , what is the peak observed at 130 cm-1?

Dear all, I have noticed, as the ZnO content increases, the Raman intensity at 100cm-1 also increases. However, there is a peak nearby at 130 cm-1, which I could not find in any paper related to...

28 July 2024 5,410 1 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

Nleonu Emmanuel Chile

I think water gives good dispersion of ZnO and TiO2.

Doaa Abdulkareem Dagamseh

Did this answer for anti corrosion mild steel ???

V R Arun Prakash

You want to coat these nano oxides on mild steel means better go for epoxy solution to dissolve the partickes and then yiu can apply the mix on mild steel. It is a easy and best way to coat

Best

Arunprakash Vincent