Why the difference between degrees of nonclassicality of the input states is required for nonzero entanglement in the output state of a beam splitter?

By considering two single-mode Gaussian states at the input of a beam splitter, it is seen that the entanglement of the output two-mode Gaussian state depends on the difference between the degrees...

22 January 2021 3,490 3 View

Hi Everyone. I want to conduct DEMATEL analysis for my survey. Everything is in line except the MAXIMUM MEAN DE-ENTROPY (MMDE) ALGORITHM. Need help ?

I can't find any manual or procedure on how to conduct the MMDE process. It looks like most of the literature has copy-pasted the stuff without any method of how to do to it. Any practical book,...

07 January 2021 1,804 2 View

Does anyone have experience in infecting suspension cells (like THP-1 or K562 etc) by retrovirus?

I am trying to make stably expressing cell line of my gene of interest in Suspension cell line using retrovirus but i don't have recommended protocol. I have searched literature but mostly they...

14 December 2020 8,274 3 View

Hello I have a question about solar cells (perovskite solar cells) modeling in COMSOL?

I have done all optical simulations in RF module, now how can i find generation rate of electrons and holes, secondly how can i use these generation rate in semiconductor module to find further...

11 December 2020 6,652 3 View

Can a mathematical model be added to a paper on bean genetic and diseases manuscript?

Can a mathematical model be added to a paper on bean genetic and diseases manuscript?

10 December 2020 2,300 14 View

Straight chain or Ring peptide for inhibiting a homo-dimer of a 20 KDa secretory protein?

I am designing a small peptide to inhibit a homo-dimer of a small secretory protein (about 20 KDa). I need suggestions on, which option would be better? a straight-chain peptide or a ring-shaped...

03 December 2020 4,145 5 View

Could someone share the Sliding Mode Control's Book?

Hello Everyone! Hope you all doing well. I want to study the sliding mode control for controlling UAV Quadrotor. I shall be very grateful if someone share the best and easy to understand book....

21 October 2020 4,383 4 View

Precipitation of sugar contents from Fruit extract?

I have to perform In-vitro and In-vivo anti-diabetic activities on 99%, 70% and 50% ethanolic fruit extracts but I need to precipitate sugar contents first. Can anyone help me with the protocols...

18 October 2020 6,697 5 View

Meshing Problem in Comsol.?

I am working on electrical streamer discharge but it gives errors. Anybody can help me out.Kindly

18 October 2020 5,672 2 View

What can be the new paradigm of Error Correction Coding after LDPC and Polar codes ?

As there is a lot of research on LDPC and Polar codes. First of all which coding scheme will lead for applications like 5G and 6G. Secondly can there is be any new paradigm of coding other than...

07 October 2020 6,175 7 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View