Dear Researchers.
There are many procedures for Extracellular polymers extraction. Such as 2% EDTA, 3% NaCl, 0.5N HCl, 0.5N NaOH, Ultrasonication and Heating.
You can extract the cell bound EPS using 20mM EDTA followed by isopropanol precipitation. It works well and it is non destructive.
Comparison of extraction methods for quantifying extracellular polymers in biofilms
Xiaoqi Zhang*, Paul L. Bishop*, Brian K. Kinkle**
http://www.sciencedirect.com/science/article/pii/S0273122399001705
Polymeric film such as latex rubber substrate or polymer
01 July 2024 8,343 4 View
FeCrAlloy® foils are commonly used for fabricating metallic monoliths. However, their lack of specific surface area/roughness (pores) hinders catalyst adhesion during the coating process. Several...
22 May 2024 8,462 1 View
How to download Lung cancer (LUSC) gene expression data which includes tumor tissue samples and corresponding control tissue samples from TCGA(https://portal.gdc.cancer.gov/repository). Any...
13 May 2024 2,481 1 View
If anyone want to know about this topic you can ask me.
23 March 2024 5,008 5 View
In one of the boundaries, Saturation, S =1 for time (t
19 March 2023 9,715 1 View
I have been working with a transgenic mice which receive seven days treatment with an antibiotic. After seven days I collected blood in the serum collection tube. After centrifugation I found...
04 February 2023 1,011 1 View
I'm having trouble doing network analysis due to topological errors. I am using ArcGis software.
23 December 2022 8,250 2 View
What is the Positive & Negative control for G2A Knockdown & Overexpression?
17 February 2022 2,374 2 View
During the wicking of liquid, it goes up due to capillary force. It is required to apply pressure at the interface of liquid and air. The position of this applied pressure changes with time.
10 November 2021 5,393 3 View
I am using PHI nano TOF II TRIFT SIMS from Physical Electronics, MN, USA. I have grown Phosphorus doped silicon thin film (200nm) on glass using HWCVD. I need to detect P-31 isotope along with the...
30 March 2021 1,346 4 View
Is it appropriate to place the ATG codon in front of the gene of interest, since there is a secretion signal that has its own ATG in front of this gene? I need my protein of interest to be...
10 July 2024 3,050 5 View
Is there research on the use of polymeric materials in dams?
19 June 2024 1,135 1 View
Hello to everyone, I'm trying to extrtact total RNA from sEVs. I made a first experiment starting from 2x10^10 sEVs quantified by NTA but the RNA obtained was very low (under 20ng/ml) Do you have...
18 June 2024 2,799 4 View
Hi, I am doing western blotting of isolated extracellular vesicles, and I have albumin and calnexin contamination that I don't know why. Is there any way to avoid it?
16 June 2024 9,907 4 View
Please give some insight on this
06 June 2024 2,016 2 View
I have prepared some polymeric microspheres from chitosan and PCL. However while performing in vitro degradation study, I found difficulties in both above mentioned methods. Here I am mentioning...
20 May 2024 6,114 4 View
Why does a polymeric material exhibit more than one peak in zeta potential measured using DLS? The material shows a single peak in acidic conditions but displays three peaks in basic pH. What...
17 May 2024 6,439 7 View
Ultracentrifugation is the most widely used method for isolating extracellular vesicles (EVs), despite the significant structural damage that EVs suffer during the process.
16 May 2024 9,432 1 View
Hi, I simulated the experiments in Abaqus. In order to see the damage propagation until failure in Abaqus for polymer materials, which damage models can be used?
25 April 2024 9,342 0 View
I tried to inhibit extracellular microvesicles(MVs) secreted from cells, through using Rock inhibitor(Y27632), calpeptin and several siRNAs(siCDC42, siTSG101, siARF1), but failed to decrease MVs....
23 April 2024 7,369 0 View