23 March 2022 2 4K Report

Looking forward to make polymer-nanocomposite based fiber film for temperature sensing in the range 25 to 40 °C. Looking for such polymer which will be flexible, and can be electrospin easily.

More Saket Phadkule's questions See All
Can I reuse DMSO heated at 45 C ?

I have used DMSO to treat films with DMSO vapour. Can I use that same DMSO solution multiple times again?

04 April 2024 5,882 2 View

We want to make an array of interdigitated electrodes (IDEs). What is a suitable simple design for it?

We want to make an array of interdigitated electrodes (IDEs), to make an array of sensor. What is a suitable design for it? How IDEs should be connected to each other? How to take connections or...

31 January 2023 6,031 0 View

How to transfer the prepared nanofiber film on the other polymeric substrate?

What are different ways of transferring the flexible nanofiber film on the flexible polymer substrate effectively, such that good adhesion between film and substrate is established?

10 April 2022 884 3 View

Is there specific force below which piezoelectric characteristics are not significant in PVDF ?

Want to use PVDF as a flexible temperature sensor due to its excellent flexibility and pyroelectric properties. But at the same time, it is piezoelectric too. When using as a temperature sensor...

03 April 2022 8,966 1 View

Is PVDF good option for making flexible temperature sensor based on nanocomposite though it is piezoelectric?

PVDF is both piezoelectric and pyroelectric. But being piezoelectric when the sensor is bent, won't the pressure/strain compound the temperature effect? Is there a particular temperature range...

21 March 2022 2,448 0 View

Why PVDF solution prepared for electrospinning becoming non-spinnable almost after an hour of preparation?

I am preparing PVDF solution for electrospinning by mixing 20 wt% PVDF in 7:3 DMSO:Acetone and stirring it at 75°C and 1000 RPM. But every time almost after an hour of preparation it is turning...

29 December 2021 5,572 4 View

In electrospinning after depositing nanofibers on Al foil, after how much time the foil can be taken out from the mandrel?

In electrospinning after depositing nanofibers on Al foil, after how much time the foil can be taken out from the mandrel? Can we keep it on mandrel for some time to get the collected mesh solidified?

16 December 2021 4,687 6 View

Can we reuse the needle used in electrospinning?

I'm doing electrospinning on the same material but needle is getting blocked everytime maybe due to solidification of polymer inside it. Is there anyway to reuse it or each time we need to use new...

16 December 2021 9,506 7 View

Can we use electrospun PVDF mat for temperture sensing? If yes, how to make an effective PVDF solution for electrospinning?

Can we use electrospun PVDF mat for temperature sensing? If yes, how to make an effective PVDF solution for electrospinning?

14 December 2021 3,583 3 View

Similar questions and discussions
What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

How can I better use imageJ to get good result on calculating surface area of a film accurately?

I have images of film formed on the bottom of a 50mL beaker, and I have been trying to figure out the surface area. I could easily use features on imageJ to do that, but I want to know which area...

23 July 2024 4,461 1 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View

Why can't I detect the plasmon resonance angle with water?

I am trying to measure the plasmon resonance angle of gold film and pure water using the Kretschmann configuration and a 633nm laser. Without flowing water over the gold, I can detect a clear...

10 July 2024 4,719 3 View

I want to ask why the poly aniline film does not stick to the ITO type substrate knowing that I used the electrodeposition method?

In order to make a polyaniline film, I used the electrodeposition method and set all the conditions, but I noticed that the polymerization process is happening, but it doesn't stick to the...

09 July 2024 2,708 2 View

How to solve Bubble Error in fiber splicing?

I'm having a bubbling error while splicing 100/350 um optical fiber (core/cladding) on ​​the Fujikura FSM100P+. I have tried some ways such as changing Prefuse power and Prefuse time but to no...

03 July 2024 7,463 6 View

What is polymer/chemicals can increase the swelling index of a polymeric film?

Polymeric film such as latex rubber substrate or polymer

01 July 2024 8,343 4 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

What are the potential effects of atomic-scale defects on the electronic and optical properties of thin films in emerging semiconductor materials?

Despite significant advancements in thin film deposition techniques, the precise role and control of atomic-scale defects in determining the properties of emerging semiconductor materials remain...

01 July 2024 5,745 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close