Which method of coating is the best suggested for coating Reduced Graphene Oxide (RGO) on a Titanium material?

More Nithesh Naik's questions See All

Which method of coating is the best suggested for coating on a Titanium material?

I want to coat Titanium with RGP Graphene Titanium Nitride Hexagonal Boron Nitride for implant orthopedic applications. Please suggest best methods for the above

04 May 2019 3,412 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

What is the best surface to culture cells isolated from a skin biopsy?

Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...

26 February 2021 6,151 2 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

Haider Abdulkareem Al-Mashhdani

I suggest EPD

Zoraida P Aguilar

The answer to your question depends on why you want to coat the RGO on Ti. First, analyze why you want to coat it. Next, analyze what the surface charge is before coating. Then. find out what materials are best for these conditions.

Ahmed mohammed Jasim

What is the clue of coating TiO2? By itself a stable