Dear researchers
In order to measuring mediating role of variable in conceptual models, which method is much more validated and better to use? if you have any beneficial links or online notes about testing mediating variable, please share it.
You can either use structural equation modeling or Hayes’ Process macro. Both are equally good.
Teddy Lian
Thank you so much for your kindly response.
I agree with looking at Hayes's Process macro. This is a good starting point too: http://davidakenny.net/cm/mediate.htm
Dear Dr Guy Curtis
Thanks a lot for your kindly response.
1.The topic I am going to research is "Advanced Gray Wastewater Treatment Output from the Biological Process by Iron-assisted surface adsorption and UV/H2O2". I think this method has been used a...
08 July 2024 9,464 1 View
I used forcite module of Material Studio software to simulate the dissolution of zinc production waste in deep eutectic solvent. UFF force field has been used for the optimization of molecules,...
02 July 2024 7,493 1 View
Fjkvchj
12 December 2023 224 1 View
Hello dear researchers, Do you know how to solve and prove the formula 5.27 (The Volume Expansion Coefficient for Low Solute Concentration) mentioned in the "diffusion mass transfer book" by...
18 November 2023 302 2 View
I hope that if you know of a postdoctoral position in the field of psychology, you will introduce me to it
31 October 2023 5,188 0 View
Hi, I would like to know how I can order a siRNA (5 or 10 nm) for a protein(X) based on the following information that has been published: " siRNA against X was synthesized from the following...
07 July 2023 5,842 1 View
Hello everyone I am a master's business management from Sapienza University. I want to make a new proposal for applying Ph.D. in field management. I am thinking that traditional training ( teacher...
13 June 2023 8,214 4 View
What analysis, SEM or TEM, is better for MOF identification? Unfortunately, I only have one choice. I have the crystal size average with XRD, and therefore, I think SEM is better. please help me.
25 May 2023 9,391 4 View
Enzymatic modification of starch: A green approach for starc...
30 April 2023 8,258 1 View
I've been asked to design and build a rigid solid frame to test our reinforced masonry walls in the laboratory. the frame's span is 8 m and its Heigh should be at least 3.5 m. I know that our...
30 December 2022 5,942 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,114 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,004 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,047 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 717 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 452 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,027 4 View
AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...
31 July 2024 9,733 3 View