Which Evacuation Model is the most known and used?

Ruggiero Lovreglio @Ruggiero_Lovreglio

01 January 2018 1 8K Report

Help us answering this question filling this survey: https://goo.gl/ykrsbP

It will take only 10 min of your time!

Many thanks

Ruggiero

Ruggiero Lovreglio

More than 140 colleagues have provided an answer to this research question. Please tell us your experience filling the survey:

https://goo.gl/ykrsbP

Badges
Science topic

Similar topics
Statistics
Survey

More Ruggiero Lovreglio's questions See All

Book describing statistical hypothesis tests?

Dear all, could you please suggest a book describing statistical hypothesis tests? Basically, I am looking for a book which describes all the tests you can use to verify an hypothesis (e.g....

07 August 2015 2,517 6 View

What software can I use for ANFIS calibration?

I would like to know which tool (software) I can use to calibrate a fuzzy model by using ANFIS. I have seen that MATLAB includes the ANFIS tool box but there are some limitations. Do you know any...

04 May 2014 7,045 13 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

A paper on a fossil lycopod?

Dear all, Does anybody have a pdf of this paper? Wood, G.R. and Beeston, J.W., 1986. A late Permian lycopod cone Skilliostrobus sp. cf. S. australis Ash 1979 from Queensland. Geological Survey of...

07 August 2024 4,857 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View