Which corrsion testing method will be preffred for testing of Eutectic Al-Si based Composite material?

04 October 2024 1 2K Report

Researchers have performed different corrosion tests such as potentiodynamic, electrochemical impedance spectroscopy, immersion and salt spray to explore the corrosion rate.

Özgün Ceren Akbay

Dear Mr Rahul Patil

In addition to the methods you mentioned, the Gravimetric (Weight Loss) Test method can also be used. This test method measures how much weight loss the corrosion causes on the material over a certain period of time. It is a simple and effective method to understand the long-term effects of corrosion on Al-Si based composites. The weight loss of the material can be measured by corroding the samples for a certain period of time and then cleaning the corrosion products.

I wish you good work.

Kind Regards.

Badges
Science method

More Rahul Patil's questions See All

What are the roles of both Monetry and Fiscal Policy coordination in optimising the Macroeconomic outcomes in the economy ?

These days policy coordination is becoming necesssary on different front. In India also it is the same case. Monetary and Fiscal policy interface is important in order to address the...

30 July 2024 2,104 6 View

How to estimate sample size for GWAS of continuous and discrete traits? What are the pre-requisites?

Genome-wide association study (GWAS) Continuous traits: eg. Height Discrete traits: eg. Eye color

28 July 2024 286 0 View

Can we fit a gaussian Fit on a LIBS Peak ?

Though much literature suggests fitting a Voigt profile on a LIBS peak, is it also possible to fit a Gaussian profile on the LIBS peak? I have 204 spectra files, and I am building a pipeline for...

23 July 2024 6,127 1 View

Can the MDFT mental health care model help reduce drug addiction?

This question might come up in my research on "Frustration, Fantasy, and Drug Addiction," where I'm also trying to figure out how to overcome mental health issues without turning to drugs.

30 June 2024 5,936 0 View

What is the effect of redshift on the evolution of an AGN?

AGN (Active Galactic Nuclei) are high energy galaxies powered by supermassive blackholes. The evolution of a galaxy is characterized by parameters such as luminosity and redshift. The redshift is...

25 June 2024 3,782 2 View

Why is my phage library obtained at round 2 of Biopanning viscous?

After incubation of the TG1 cells with the helper phage, I spun down the culture and precipitated the supernatant with PEG/NaCl. After this, I spun it down again and resupended the pellet in PBS....

21 June 2024 6,260 2 View

Which smoothening model is acceptable for processing of circular dichroism spectra?

For smoothening of noisy CD spectra, several fitting models are available in Jasco spectra manager software, like Savitzky Golay, binomial, means movement and adaptive smoothening. Each one asks...

16 June 2024 3,997 1 View

I am carrying out MTT Assay using HeLa cells but the absorbance values are really less, can anyone please help?

I have seeded HeLa cells in a calculation of 10000 cells per well in a 96 well plate. Then I went for treatment in the next day. Then at last, I added 7ul of 5mg/ml solution of MTT reagent into...

12 June 2024 1,460 3 View

Can we use LIBS Peak - Ti 441.492 for the Univarate Analysis ?

I have 17 different steel samples, in which i identified a peak of Ti 441.492. But , if you look closely at photo, while some some peak are at 441.492 , some are at the slight offset. eg 441.490...

10 June 2024 8,934 2 View

Challenges in Univariate Analysis for Stainless Steel Samples using Laser Induced Breakdown Spectroscopy?

Respected Members , I have a 17 different steel sample references , with varying concentration for Minor Elements being Mo , Ni , Mn ,Si , Cr etc , i am trying to build a calibration curve with...

10 June 2024 993 0 View

Basis set and input instruction to calculate HOMO and LUMO using Orca for Imidazolium based organic salts?

Hey there, As a synthetic chemist delving into theoretical calculations for my imidazolium-based organic molecules, I would greatly appreciate any guidance on the appropriate input instructions...

09 August 2024 5,444 7 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to remove/ replace trifluoroacetate countertop after deprotection?

After deprotection of the tert-butyl ester to generate the carboxylic acid in chloroform with TFA, my compound‘s pyridine moiety forms a TFacetate ammonium salt (small molecule drug, not a...

29 July 2024 9,753 3 View

What is the best method to detect the chemical composition of pollen ?

I have multiple small samples of grass pollen with anthers. I want to find a method to identify concentrations of proteins, lipids, and other various elements for these samples. any suggestions?

28 July 2024 5,331 1 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

What is the right voltage sweep direction for characterization of HER kinetics?

In general, when performing a Tafel analysis for corrosion resistance measurements, a line voltage scan is performed from say -250 to +250 mV vs. OCV at low scan speed around 0.125 mV/s. However,...

25 July 2024 7,982 3 View