Which best composition of material could be formed by using stir casting for MMC?

More Chintan Barelwala's questions See All

Which are the advanced objectives of parametric optimization of Wire cut EDM machining of the MMC AlSiC?

Is there any further objectives like fea of WEDM and other methodology used except optimization in Wire cut edm of AlSiC MMC material?

30 January 2023 5,971 3 View

How to categorise proteins based on the function?

Hi all, I wish to classify my proteins into the classes like the one in the attached image. I tried various bioinformatic tools including DAVID, panther, and gene ontology. However, they don't...

22 January 2023 7,101 2 View

Can I use HNO3 as solvent to make cerium oxide nano particles in sol-gel method? and the process I followed is sol-gel method or co precipitat method?

Cerium(III) nitrate hexahydrate [2 g, Ce(NO3)3·6H2O] was dissolved into 4.5M HNO3 (5 mL). Sodium hydroxide (10.50 g NaOH) was also dissolved into DI water (deionized water) (35 mL). This NaOH...

06 November 2022 8,602 3 View

What is the possible solution to the error "turbulence viscosity limited to viscosity ratio 1.000000e+05 in xxxxxx cells" in ANSYS Fluent?

Hello everyone, I am working with multi physics eulerian modelling in ANSYS. I am using k-epsilon model to work with simulation. Simulation is regarding stirring of molten Al in crucible or say...

28 April 2022 2,184 0 View

Why most of researcher used Wrought Al alloy to prepares Al MMC using stir casting process?

Wrought Al is already extruded grade then why most of researcher are not using Al cast grade And very few researchers worked on cast Al grade during stir casting. If one can given insight on why...

09 November 2021 2,138 4 View

Respiratory syncytial virus plaque assay?

Hello, I am trying to perform a respiratory syncytial virus (RSV) plaque assay. I can see the syncytial formation, white dots with a crystal violet background (3 replicates). However, I don't see...

18 October 2021 5,082 2 View

Which AlSiC compnent used in automobile, aerospace etc. manufactured by using Electric Discharge Machining Process ?

I have observed many papers in optimization of electric discharge machining on different MMC compositions. But, nowhere I found application of EDM for such parts. I want to know which AlSiC...

27 June 2021 3,290 1 View

How can we count the number of edges in an edge detected image using canny/sobel algorithm in MATLAB?

I need to process an image for edge detection and then want to count the number of edges in that image.

29 December 2020 5,961 2 View

Is there any workaround for MaxQuant when it crashes unexpectedly without giving any errors?

I am processing my MS results that were acquired in Orbitrap instrument and it seems that as soon as I start the analysis on MaxQuant, it crashes unexpectedly with any error reports. This has...

01 October 2020 8,132 6 View

How to use Fischer exact test for daily survival analysis? Can I do it in SPSS?

I want to compare survival difference daily using Fischer exact test? How do I do get using SPSS?

12 June 2020 7,348 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Usage of internal standards in LC-MS/MS analysis?

Have you ever seen a LC-MS/MS method uses both internal standards and external standards (in matrix matching purpose) but the concentrations of internal standards are outside the calibration curve...

05 August 2024 3,084 6 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Request a single Lecture notes for math as detailed as this that I can find in one place?

- The Existence/Uniqueness of Solutions to Higher Order Linear Differential Equations - Higher Order Homogenous Differential Equations - Wronskian Determinants of $n$ Functions - Wronskian...

03 August 2024 2,366 0 View

Does continues partial charging/discharging do any harm to the BESS performance and degradation?

For a grid connected BESS (lets say 100 MW/200 MWh system, LFP battery), if we charge the BESS in such a way that whenever we can access power from the solar that will charge the BESS. Hence it...

01 August 2024 9,903 7 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

Babu Bhaskaran

Refer this link:www.slideshare.net/.../preparation-of-metal-matrix-composites-by-stircas...

Refer this link:https://www.erpublication.org/admin/vol_issue1/.../IJETR011950.pdf

Refer this link:doi.org/10.15623/ijret.2014.0307058

Refer this link:www.ijeat.org/attachments/File/v3i2/B2361123213.pdf

Refer this link:www.sciencedirect.com/science/article/pii/S2238785413000616

Adalarasan Ramalingam

The real applications of MMCs start at volume fractions of around 15% or greater. A double stage stir casting can be used to cast MMCs with a relatively better distribution of reinforcements.