Where I can find an information about superhydrophobic coating research for Wind Turbines for IPS package?

11 August 2018 1 8K Report

I am doing research regarding IPS for Wind Turbines. I need any information regarding superhydrophobic coating testing for Wind Turbines.

James E Hanson

We do some work on these types of coatings - you can find a lot of background material on these coatings searching on SciFinder, Science Direct, or Google Scholar.

Badges
Science topic

More Nigar Gahramanova's questions See All

Dear Scholars,I wanted to inquire about the latest edition of Evans and Green's Cognitive Semantics (2019)?

Could you please direct me to a website where I can purchase the latest edition?

31 October 2023 311 0 View

Is there anyone how to solve ABAQUS illegal memory reference (signal 11) error in UVARM subroutine?

Dear all, We want to model a pressure vessel using WCM (Wound Composite Modeler). We have built a model by following the instructions in user manual and examples. For post processing, UVARM...

01 September 2019 7,059 3 View

What is the source of inoculum for anthracnose and black rot in grape in Pakistan?

I need inoculum of Elisinoe amplina (casual agent of anthracnose in grape) and Guignardia bidwelli (casual agent of black rot in grape).I need some information that in Pakistan from which...

28 August 2019 217 0 View

What are typical reflux ratios in industry? What are minimum and maximum values of reflux ratio can be seen in industry?

I am trying to design a distillation column, and I am not sure if the value I obtain for reflux ratio is normal or not.

29 January 2018 8,021 17 View

Could you ,please, suggest the useful source for statistics of meta-analysis for beginner?

I try to analyze the data with a binary outcome and high heterogeneity (I2=85%). Could you, please suggest me the source to perform the analysis? All suggestions are highly appreciated.

29 December 2016 5,620 13 View

Is there a difference between the pearson and spearman plot creating in stata?

Is there any difference between pearson and spearman tests when I try to create correlation scatterplot in stata or do I have to just create the scatterplot and interpret it as a lineer or...

16 October 2016 8,757 4 View

How to measure inequality of opportunity?

looking beyond the conventional measures of poverty, it seems interesting to look at the non economic factors so that a better measure of poverty can be calculated. while going through some of the...

07 April 2016 7,909 10 View

How can I do the Heat Balance of a fixed-bed, which is heated by Microwave?

Hi Everyone, I am trying to do the heat balance in my microwave heating system. The system consist of Zeolite Y fixed-bed (L:8mm,200mg) in a quartz tube (Din:7mm,Dout:9mm ), which is introduced...

18 January 2016 543 2 View

Can someone help with calibrating the Mass Spectrometer for carbon dioxide?

Hi everyone, I have still doubts about the CO2 calibration. What I do is using a loop (V=0.250ml) in a six-way valve and doing some pulses of CO2. I mean, first passing through the loop a certain...

07 May 2015 6,899 2 View

Does anyone have experience with fixed bed adsorption/desorption at the Solid/gas interface?

My fixed bed adsorbed/desorbed amount of CO2 does not match (lower than) with ASAP2020 CO2 isotherms at the same partial pressure.

02 September 2014 6,131 5 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Could you try using PeptiCloud and see if it's a useful tool for biology research?

PeptiCloud (www.pepticloud.com) is a bioinformatic platform that allows researchers to organize and share their data for their projects as well as collaborate with others in one place. Through...

28 July 2024 4,762 2 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

How to fix install package meta in R?

> library(meta) Error: package or namespace load failed for ‘meta’ in loadNamespace(i, c(lib.loc, .libPaths()), versionCheck = vI[[i]]): there is no package called ‘numDeriv’

18 July 2024 3,536 0 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View