Where can I obtain a SAS Macro Program for Modelling Multi-State Markov Processes?

More Faiyaz Doctor's questions See All

Immune system and its activity against cancer?

according to your academic experience the immune system will overcome the cancer challenge in future .

26 May 2024 2,797 3 View

How to normalize the reflectivity data by taking the fluctuations of the incident beam flux in the synchrotron beamline into account?

What is the mathematical way to normalize the reflectivity data obtained from synchrotron beamline measurements? I found that during the mesurements there is a the fluctuation in the beamline's...

21 May 2024 3,996 3 View

Do you think gene therapy will replace traditional pharmaceutical therapy in future ?

Hi tech research in this field will served as new technique of therapy .

16 September 2023 1,538 2 View

Do you think , auto-immune disease will be go to the past with development molecular science?

molecular science for future

09 July 2023 5,837 1 View

What is a future of aesthetic medicine ?

fast growth field did u think it will be continous in this form .

31 May 2022 2,584 3 View

Dermal filler cause cancer ?

there any study connected between dermal filler and skin cancer .

30 May 2022 9,145 5 View

Unable to make SCAPS-1D generate Fill Factor and Voc ?

We have been trying to use SCAPS -1D to model Perovskite cells. We have been trying to replicate the attached paper by Hossain et al. The graph we tried to generate is given next. Our simulated...

23 March 2020 7,274 4 View

Thermal conductivity of metallic powder?

I am doing some experiment for measuring temperature dependent thermal diffusivity and conductivity of metallic powders like inconel 718, TI6AL4V. What I observe is there is an increase, then...

15 March 2020 3,194 6 View

Powder packing density?

Hello, can I get powder packing density by Dividing mass by the volume it has occupied?

02 February 2020 2,726 3 View

What is cell reynolds number?

Hello, I am doing powder bed fusion simulation in COMSOL. In result section, I can see cell reynolds number. What is the difference between the cell reynolds number and actual reynolds number? How...

24 September 2019 8,102 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

"A Markov-like Model for Patient Progression"?

A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...

05 August 2024 10,079 0 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View