Where can i get SAR Wave mode image data for my current research on deriving ocean wave spectra..?

More Bhuvana Chandra's questions See All

What can be the alternate buffer for TAPS (PH 8.5) in Post tagmentation Wash step in Cut & Tag experiment ?

I am performing Cut & Tag experiment. I was wondering if there is any alternative/replacement for TAPS pH 8.5 in single tube Tagmentation and pA-Tn5 release ( DNA purification) step of Cut and...

02 April 2024 4,214 0 View

How much of primary antibody do you add on slides in immunohistochemistry(IHC) / Immunocytochemistry (ICC)?

Most of the Antibody company (having pr. Ab conc. range 0.2 mg/ml - 0.5mg/ml) websites suggests dilution around 1:200, but it seems not staining or faintly staining. What is the hand on experience...

28 March 2024 259 3 View

Why do I get minor electric shock in my laboratory when touch something metallic?

Sometimes when I touch my colleague or metal bodies. i fell shock with some minor electric sound.

27 February 2024 1,191 3 View

How to separate dead cells from live cells when propagating suspension cells?

I am growing small cell lung cancer suspension cells. How do I separate dead cells from live cells while splitting the cells after confluency in flask?

28 January 2024 8,818 6 View

How to do multiple data sequential Rietveld refinement in TOPAS?

I can do Rietveld refinement of single multiple phase data, but I am not able to do multiple data sequential Rietveld refinement. I am using Topas V7.

21 January 2024 2,083 0 View

Why does the transmittance % in FTIR become more than 100% (Opposite direction)?

I did FTIR of a reactive dye's powder. But I see that the transmittance of 3 peaks went opposite direction of normal peaks and eventually the transmittance percentage became more than 100%. What...

17 December 2023 7,093 2 View

Does a thinner intrinsic layer in a 'p-i-n' solar cell, compared to the diffusion length, lead to increased or decreased charge carrier recombination?

As we know, when the thickness of any layer in a p-n junction solar cell exceeds the carrier diffusion length, the photo-generated carriers recombine before reaching the charge transport layer....

15 December 2023 4,930 3 View

How to calculate polymorphic information content (PIC) value for SCoT marker data? Which software helps to calculate it?

I am trying to evaluate the genetic homogeneity of wild grown mother plant and tissue culture raised plants of Piper sp. using SCoT and other dominant markers.

06 December 2023 1,837 0 View

Does enthalpy of chemical sorption reaction is a strong function of pressure and/or temperature for soprtion of ammonia in halide salt?

In most of the literature the enthaply of formation/reaction is chosen to be an constant. Some researchers claimed that in a given pressure range (say: 10 bar) this parameter can be chosen to be a...

07 November 2023 8,839 0 View

Can any one help me to get access of the following in Description below ?

An Interpersonal Communication Inventory Millard J. Bienvenu, Sr. Journal of Communication, Volume 21, Issue 4, December 1971, Pages 381–388, Click Below An Interpersonal Communication Inventory

06 September 2023 6,207 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Samir Aguemoune

you can get it from ESA data archive :https://earth.esa.int/web/guest/home or https://earth.esa.int/web/guest/pi-community (and for searching data you can use EOLI free software online).

https://earth.esa.int/web/guest/home

https://earth.esa.int/web/guest/pi-community

Fabrice Ardhuin

You will find some info on Sentinel 1 wave mode here ... http://oceanwavesremotesensing.ifremer.fr/

As for the level 2 access, just ask Alexis mouche or Romain Husson at CLS.