How to find out or construct(?) the right priors from data of previous experiment to use in a bayesian glm?

I have the following equation, Eating choice (Yes/No)~ Box type (A/B/C). So the question is whether a certain box type affects eating choice in groups of dogs. The eating choice of each member in...

10 February 2021 6,024 9 View

What are the ways to test the knowledge level of agricultural labourer about their day to day work?

what kind of test can I do for testing the level of knowledge about their daily operation?

03 February 2021 7,583 10 View

Why the bandgap of CH3NH3PbCl3 films are different for spin-coating method and electrospinning method?

The observed bandgaps are 3.8 eV and 3.4 eV for spin-coated and electrospun films, respectively. What are the possible reasons?

08 January 2021 5,646 6 View

Why monoethanol amine is used as flocculant?

I want to know the reaction mechanism of monoethanol amine used as flocculating agent for rerefining used lubricating oil. Here I have attached one research paper where MEA (monoethanolamine) is...

01 January 2021 5,681 2 View

Problem with GST-fusion protein elution- Can anyone help?

18 December 2020 4,559 6 View

How can I determine metal concentration of Used lubricating oil by AAS?

I am a junior research fellow in the department of Chemical Engineering, Nit Durgapur. I want to know that how can I determine various metal such as Fe, Cr, Mg, Mn, Pb concentration present in...

15 December 2020 9,887 3 View

Regarding the O 1s XPS pf phyllosilciates, the peak near 531 belongs to Oxygen vacancy sites or O bonded to the Si from the silicate tetrahedra?

In O 1s spectra, usually the peak near 531 eV belongs to oxygen vacancy sites in oxides, however, in silicates, these peaks are often reported to originate from O-Si. I am confused if the intense...

10 December 2020 9,496 2 View

What is the mol. weight of GFP-11 tag?

Hi, I am trying to find out the mol. weight of GFP 11 because it is tagged to my protein of interest which is 17kDa. GFP 11 has been tagged with my protein of interest while GFP 1-10 is tagged...

09 December 2020 1,863 1 View

How to PEGylate Fluorescntl Polystyrene Particle?

I have Fluorescent Polystyrene beads. I need to graft PEG on the surface of it. I am looking for a protocol to do that. Also need to know which experiment to perform to be sure about the grating.

01 December 2020 7,860 1 View

How to control for categorical independent variables (e.g., education) when doing regression discontinuity using STATA?

I am conducting a regression discontinuity design where the dependent variable is continuous while control variables are categorical (except the treatment variable). In the usual regression...

01 December 2020 583 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View