Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Can I arbitrarily take a cycle number of 40 for the gene that was not expressed at all in qPCR results calculation?

I ran RT-qPCR for a control and a treated group and it appears that my gene of interest was not expressed at all in any of the subjects in the control group. So I was wondering if I could...

20 February 2021 6,243 10 View

Does anyone know if the Quantstudio 3 qPCR machine requires a passive reference when Using SYBR? I ran a qPCR and got the plot in the attached file.?

I know that my target is in my sample as I extracted it from cell culture myself. These plots show some amplification. The first one seems O.K for the first 36 cycles but then collapses at the...

14 February 2021 2,809 2 View

Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

What is the reference value of THD in BLDC MOTOR speed control ?

i used to control EHO+ANFIS to MRPID to Landsman converter for bldc drive i got 7% but some of them are telling IEEE standards are < 5% is it correct for Drives ?

07 February 2021 5,892 1 View

Having trouble with qPCR amplification plots. My curve's never seem to reach a plateau. Any ideas?

The parameters of the curve all seem acceptable, typically reactions results are above 0.9852, -3.1 to -3.6 slope, and 90-110% reaction efficiency. The results seem to be what I would expect from...

04 February 2021 1,138 3 View

Queries regarding the rain flow counting algorithm?

02 February 2021 9,790 2 View

Can't run my IPMSM drive system with DC-supply higher than 125 V. Have anyone had similar problem?

Hey, I try to run my 4 pole IPMSM with PWSVM and use a typical controller with PI-controller with a current loop and speed loop. When I run my system with DC-supply 100 V with a steady-state speed...

28 January 2021 7,354 8 View

How to build a Jupyter Notebook page to access remote Molecular Dynamics results?

Hi all, I am hoping for some assistance. I (the researcher) would like to know whether it is possible and how to go about building a Jupyter Notebook that a collaborator could load in their web...

26 January 2021 1,027 1 View

PCR primers bind to specific DNA at specific temperatures but not other temperatures?

I ran PCR in order to analyze a P-element excision on a mutant drosophila line. My results were not conclusive, however that is beside the point. I ran a temperature gradient in order to optimize...

25 January 2021 9,164 11 View

HPLC: how to calculate violaxanthin area if it overalps with neoxanthin?

Does anybody know of, or have a method suitable for HPLC analysis that allows to separate violaxanthin from neoxanthin? I want to quantify the xanthophyll cycle (violaxanthin, antheraxanthin and...

21 January 2021 5,775 5 View