Where can I find a motor like this?

08 April 2020 0 9K Report

I'm designing a control rod drive mechanism to drive a 9m control rod of 720 kg in mass at 5 mm/s constant speed. To have a 2 stage gearbox I need a motor that has 50-100 rpm, low power output, low torque and at least have a mass of 60-100 kg. Where can I find a motor like this and please comment if the motor i'm looking for will be feasible for my project.

Badges
Science topic

Similar topics
Electrochemistry
Battery

In frequency domain alpha band(8-16hz), beta band(16-32hz), gamma band(32-64hz), sub-band(64-128hz) are same as LL,LH,HL,HH in wavelet decomposition?

I am working on single trial motor imagery data i.e. EEG data. I am following a paper which has a dataset from BCI challenge IV (dataset 2b). After removing noise and extracting all the data from...

23 February 2021 5,503 1 View

Suppose we have a banana seller cart consisting of 4 wheels, weighing about 300 kg. How much torque motors are needed to pull of push it electrically?

I am thinking of electrifying the street food carts while harvesting energy using solar panels on top.

22 February 2021 4,323 3 View

Can you please suggest me how to convert EDF file into Mat file for EEG datasets?

Hi sir, 1.can you please suggest to me how to convert the EDF (European Data format) file into a Mat(Matlab) file for EEG datasets?. 2. Also suggest some publicly available EEG Motor Imagery...

15 February 2021 7,620 1 View

Is Genetic Algorithm usage for Motor Conception FEA optimization a good choice?

Hi RG community, Like the title shows ,i was wondering if choosing the GA for this kind of Optimizaiton is a good choice? For example we have a population of 100 (for 7-8 Optimization Variables),...

14 February 2021 1,160 7 View

How to interface ANSYS Maxwell and Matlab?

Dear All, I am working on electric motor design in Ansys Maxwell. I have written optimization code in MATLAB. I want to run this code in ANSYS MAXWELL and generate FEA results. Does anyone know...

10 February 2021 1,279 1 View

How can I prevent my switching power supply from sudden voltage increases ?

Hi Everybody, I'm currently using a 3kW AC/DC converter which gave 48VDC output(Switch mode power supply). The device is capable to deliver up to 62.5A current to the load. My application is a...

08 February 2021 7,642 4 View

What is the reference value of THD in BLDC MOTOR speed control ?

i used to control EHO+ANFIS to MRPID to Landsman converter for bldc drive i got 7% but some of them are telling IEEE standards are < 5% is it correct for Drives ?

07 February 2021 5,892 1 View

Can't run my IPMSM drive system with DC-supply higher than 125 V. Have anyone had similar problem?

Hey, I try to run my 4 pole IPMSM with PWSVM and use a typical controller with PI-controller with a current loop and speed loop. When I run my system with DC-supply 100 V with a steady-state speed...

28 January 2021 7,354 8 View

Can I project all raw motor imagery EEG data onto two spatial filters developed from training data?

Greetings RG community, I have been working on a pipeline for the classification of EEG motor imagery signals. This is currently being done on the Giga Science MI dataset with 52 subjects, using...

28 January 2021 6,947 2 View

How to build a Jupyter Notebook page to access remote Molecular Dynamics results?

Hi all, I am hoping for some assistance. I (the researcher) would like to know whether it is possible and how to go about building a Jupyter Notebook that a collaborator could load in their web...

26 January 2021 1,027 1 View