When I dope a sample, for calculation of the weight percentage do I need to consider the water content as well?

More Sandip Pchoudhury's questions See All

Change of intensity with doping?

Dear Researchers, I have my samples SnO2 doped with with Cu (1, 2, & 4%). The peak intensity reduces in XRD for 1 and 2%. However, for 4% additional peaks appears which I believe is due to...

05 June 2019 4,806 3 View

CNT-metal oxide combo?

Dear Researchers, Since CNT is not soluble in standard solvents like DI water, ethanol etc, how do I make a doping/composite of CNT and metal oxide. Your suggestions will be highly appreciated....

05 June 2019 6,386 2 View

How to measure the amount of sample (quantum dots) in a solvent?

I have quantum dots dispersed a solvent. If I am considering 2 ml of the solvent, then how do I find out how much is the amount of sample in that solvent? I tried drying the sample to obtain...

03 April 2019 4,333 8 View

Which solvent to dissolve Co3O4 and NiO?

Some literature and RG search mentions a acid solution for dissolving Co3O4 and NiO. Also, for Co3O4 I tried a basic medium of pH 10, but was unable to dissolve. I am not sure incase I am using...

10 November 2018 4,297 0 View

SAED Image analysis?

Dear Sir/Mam, Considering the scale, we measure the distance between the centre and the bright spot of the diffraction pattern. This should tally with the reciprocal of the d-spacing and the...

07 August 2018 3,371 2 View

High temperature hydrothermal reactor?

Kindly let me know the details along with an image of a high temperature hydrothermal reactor operating at 400c to 500c. Thanks and regards

06 July 2018 5,765 3 View

Measurement of Size of Quantum dots?

Dear Sir/Mam, I have synthesized some quantum dots suspended in solvent (DI water) . I am interested in finding the size of those dots. One way would be offcourse HRTEM. But I am interested in...

05 June 2018 8,740 3 View

Synthesis of Graphene Oxide - not by Hummers method?

I am interested in synthesizing Graphene Oxide but not by Hummers method. If any one can suggest from his/her expertise. Also, does other method or even Hummer method ensure a good quality. Also...

05 June 2018 2,962 0 View

Screen printers and gas sensing setup?

Dear Sir/Mam/Colleague, What kind of Screen Printers do I use to deposit thin films? If possible provide me with a link of the description of the instrument. Also, what will be the approximate...

09 October 2017 9,136 0 View

Writing a project?

I worked on metal oxides and its application for gas sensors. Now I intend to write a project, and found Bio-sensors (using metal oxide) as a very interesting project. My doubt lies, whether the...

07 August 2017 5,478 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Is there a classification scheme for rock cavities or caverns with respect to their size and shape?

The range of forms and sizes of cavities in rock is very big. Is there a classification scheme for rock cavities regarding their size and shape?

02 March 2021 4,511 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View

Dinesh Kumar Dixit

While calculating the weight percentage, I think we need to consider the water content for sure. For example, say, in an reaction if we have some gaseous products which evolve as byproducts, we consider them for the weight percentage too. So you need to consider the water content too, if you have that in your material.

Sandip Pchoudhury

thANKS....

Tejinder Singh

Ofcourse