Change of intensity with doping?

Dear Researchers, I have my samples SnO2 doped with with Cu (1, 2, & 4%). The peak intensity reduces in XRD for 1 and 2%. However, for 4% additional peaks appears which I believe is due to...

05 June 2019 4,806 3 View

CNT-metal oxide combo?

Dear Researchers, Since CNT is not soluble in standard solvents like DI water, ethanol etc, how do I make a doping/composite of CNT and metal oxide. Your suggestions will be highly appreciated....

05 June 2019 6,386 2 View

How to measure the amount of sample (quantum dots) in a solvent?

I have quantum dots dispersed a solvent. If I am considering 2 ml of the solvent, then how do I find out how much is the amount of sample in that solvent? I tried drying the sample to obtain...

03 April 2019 4,333 8 View

Which solvent to dissolve Co3O4 and NiO?

Some literature and RG search mentions a acid solution for dissolving Co3O4 and NiO. Also, for Co3O4 I tried a basic medium of pH 10, but was unable to dissolve. I am not sure incase I am using...

10 November 2018 4,297 0 View

SAED Image analysis?

Dear Sir/Mam, Considering the scale, we measure the distance between the centre and the bright spot of the diffraction pattern. This should tally with the reciprocal of the d-spacing and the...

07 August 2018 3,371 2 View

Measurement of Size of Quantum dots?

Dear Sir/Mam, I have synthesized some quantum dots suspended in solvent (DI water) . I am interested in finding the size of those dots. One way would be offcourse HRTEM. But I am interested in...

05 June 2018 8,740 3 View

Synthesis of Graphene Oxide - not by Hummers method?

I am interested in synthesizing Graphene Oxide but not by Hummers method. If any one can suggest from his/her expertise. Also, does other method or even Hummer method ensure a good quality. Also...

05 June 2018 2,962 0 View

Screen printers and gas sensing setup?

Dear Sir/Mam/Colleague, What kind of Screen Printers do I use to deposit thin films? If possible provide me with a link of the description of the instrument. Also, what will be the approximate...

09 October 2017 9,136 0 View

Writing a project?

I worked on metal oxides and its application for gas sensors. Now I intend to write a project, and found Bio-sensors (using metal oxide) as a very interesting project. My doubt lies, whether the...

07 August 2017 5,478 0 View

Synthesis of SnS3?

What are the possible ways to synthesize doped SnS3 by simple chemical synthesis without use of hydrothermal reactor. By ways I mean what kind of chemicals. (An acetate or a chloride compound...

01 February 2017 2,224 1 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Anyone plz suggest relevant topic for research in image processing+Deep learning.?

I have selected brain tumor images ...but now found that already lots of research done n this topic.

03 March 2021 5,774 3 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View