What should be the boundary condition for torque analysis of concentric cylinder in abaqus and how to apply load?

08 August 2017 1 4K Report

I am doing torque analysis of concentric cylinder of Dual materials so regarding loading and boundary condition in Abaqus I am getting the problem.Regarding I need suggestion.

Sumit Kumar

But @Chirag Sachdeva i have to apply moment to internal cylinder

Badges
Science topic

More Sumit Kumar's questions See All

How to write udf code for Pulsatile blood flow simulations?

Hi, I am working on blood flow simulation based on CT scan data. I want to know how to write udf for Ansys fluent simulations for pulsatile flow conditions. Thanks

10 November 2019 5,734 3 View

How to simulate Fluid structure interaction problem in human artery by ansys fluent ?

Hi, I am using CT/MRI data for 3D modelling. I have modelled 3d File for simulation , i want to know FSI simulation setup on ansys fluent.

05 June 2019 3,838 3 View

How to couple air and structure in abaqus?

Hi, I want to do air structure interaction of human ear i have modeled 3d input file fro abaqus using MIMICS Software. But after importing in abaqus how to couple the bone, cartilage and air each...

09 October 2017 1,742 0 View

Modeling of 3D file abdominal artery and meshed using tetrahedral element using 3matic?

Element size I have selected 1 mm in 3MATIC but for solving CFD in ANSYS not getting the converging result of simulation I have set residual value as 10e-6 but not getting.I am getting 10e-4.So...

10 November 2016 9,956 1 View

I have stl file of Abdominal aorta, i want to do meshing in ansys so what to do?

ANSYS CFD

01 January 1970 5,035 1 View

How to convert .stl file into .igs file for cfd analysis?

Bio-mechanics

01 January 1970 5,252 2 View

From where i can get blood flow properties based on gray value ?

Related to simulation in CFD

01 January 1970 8,823 3 View

How to create plane according to geometry in post processing in ansys fluent?

I want so result at various plane section in ansys fluent so please guide me

01 January 1970 3,392 0 View

How to decide meshing type and all detail for CFD analysis?

Abdominal aortic 3D Fluent analysis

01 January 1970 6,924 0 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View