What sequence is used to measure Magnetic switching effect in SQUID or PPSM?

25 February 2025 0 6K Report

I need the sequence utilized in DynaCool software to measure the magnetic switching effect shown in figure.

Both SQUID and PPMS follow the same code.

Badges
Science topic

More Ruqaiya Almamari's questions See All

Dear All, kindly I want two protocols: 1. Polymorphonuclear leukocytes (PMNs or neutrophils) extraction from blood. 2. Degranulation of PMNs?

The objective: To compare the antimicrobial peptides compositions in neutrophils with stimulation and without stimulation.

19 September 2023 1,621 2 View

Which dodecahedron or cuboctahedron is used to describe the oxygen polyhedral surrounding La3+ in LaFeO3?

In some articles, the oxygen cage surrounding the rare-earth ion in orthoferrites like La3+ in LaFeO3 is described as dodecahedral, whereas in others, it is described as cuboctahedral. Which...

10 February 2023 9,642 3 View

Tight binding calculation for a perovskite, any help???

Hello I want to do a tight binding calculation for a rare-earth perovskite (ABO3). How can i set the matrix for the unit cell? I started first by sitting the hopping elements of one octahedral,...

12 November 2017 1,876 0 View

I need help with this problem? Thermal Advance ?

Air enters the compressor of a regenerative air-standard Brayton cycle at 100kPa,300K. The compressor pressure ratio is 10. The turbine inlet temperature is 1400K. The isentropic efficiency of the...

28 September 2017 7,939 2 View

How do u clean the milling ball vial?

I prepared some compounds like perovskites using the planetary ball mill. Usually, I set the machine up to 300 rpm with 7 to 9 balls for different long times. The problem, when I finish the...

20 March 2017 9,001 6 View

Veeco Nanoscope IIIa Troubleshooting -- How to Fix Not Turning On?

My school recently acquired a Veeco Multimode and Nanoscope IIIa. While our software and computer is set up and working, the actual Nanoscope is not powering on. We currently have it wired up, and...

19 June 2024 592 0 View

I am running a IV characterization for RRAM device. The switching for only the first cycle is good. I couldn't figure out what is wrong. Help?

I have tried changing compliance current, delay. But I still couldn't figure out.

27 May 2024 512 0 View

How to reduce notches in input AC voltage for Totempole Power factor Correction circuit?

Respected readers, I am working with a totem pole PFC circuit. In an experimental study, I face a problem of high-frequency notches in source voltage (Yellow one). I found an explanation behind...

14 May 2024 6,692 6 View

How can we study the switching probability in a MTJ?

I am doing a micromagnetic study of influence of different physical and material parameters on switching in MTJ on OOMMF. Further i wanted to extend my work to studying the switching probability...

12 May 2024 6,896 0 View

Inclusion of DMI (Dzyaloshinskii Moriya effect) in STT MTJ on OOMMf?

I am studying the switching mechanism in STT based perpendicular MTJ through the micromagnetic platform OOMMF. I wanted to know if there is a way i can include the DMI effect to observe it's...

12 May 2024 1,642 0 View

What considerations should be made when switching a patient from another antipsychotic medication to Olanzapine?

Comprehensive Review of Olanzapine: Clinical Considerations ... What considerations should be made when switching a patient from another antipsychotic medication to Olanzapine?

10 May 2024 429 1 View

The modal switching problem for multimodal robots ?

How does an amphibious robot with two sets of power units rationally switch between them? Or the modal switching problem for multimodal robots?

05 May 2024 4,625 2 View

Warning and error DMol3 message?

hi people, I am doing a geo optimization in DMol3, the calculation seems to converged, but I got a warning and error message like the following, can someone explain me what that means? and what...

29 April 2024 6,680 4 View

How to calculate switching and conduction losses of an three phase inverter?

calculation of switching And conduction losses in a three phase inverter. and also how to calculate these two losses in matlab. means how to prove theoretically and practically

12 March 2024 720 0 View

Maximum ODs and growth kinetics in Terrific broth?

Hello, I am switching to Terrific Broth (from LB) to grow cultures for Gigapreps. I will grow 1L culture in 2.8 L baffled Erlenmeyer flasks for maximum aeration. What is the maximum OD I...

27 February 2024 8,500 0 View