What is the right way to conjugate two acids?

How to conjugate two acids with amine linker?

18 February 2021 4,083 2 View

What is the method of removing RNase contamination from a filter paper surface?

I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...

12 February 2021 3,926 3 View

What is causing the raw fluorescence to be negative?

Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...

09 February 2021 4,642 3 View

Regarding immunology, transmissivity, herd immunity and vaccines in Sars CoV-2?

This is a follow-up on an earlier question regarding mechanistics of vaccines: why current vaccines don't block transmission. In summary, they don't engage mucosal immune cells to produce IgA....

08 February 2021 8,321 3 View

What is the critical deficiency limit in soil for Mn in wheat crop ? in terms of DTPA extractable Mn?

critical range for Mn in soils is 2.5-4.5 ppm for all plants as an average, but what is the exact amount of DTPA extractable Mn in soil for wheat crop

04 February 2021 4,008 4 View

Which solvent is suitable for product precipitation if reaction has been performed in toluene?

If condensation reaction happened between carboxylic acid and amine and amide is formed. The solvent for this reaction is toluene. After completion of reaction, how to collect product? It should...

03 February 2021 9,796 3 View

How can I enter the load increment values to the Abaqus?

In Abaqus I know that there are two methods for incrementation (Automatic and fixed incrementation). I want to control the incrementation by myself. I want to input the values of load increment...

03 February 2021 6,943 3 View

Distortion problem in Abaqus explicit?

Dear all. I'm modeling the RC column with cyclic displacement by Abaqus-Explicit. The concrete model used Concrete Plastic Damage model. However I'm facing with a error about the excessive...

01 February 2021 7,726 1 View

Why does the ghost atoms gives error in NICS calculation with wb97xd in gaussian09 ?

In a trial, I am trying to calculate NICS (0 and 1) values for benzene ring using gaussian09. I have placed the ghost atoms at the center, 1A, and 2A above the rings. On using the method/basis...

19 January 2021 3,188 3 View

Electroactive surface area of bare and the synthesized material?

For electrochemical sensors, the electroactive surface area (ESA) show higher value for the working material as compared to bare (reported in several papers). My bare electrode is FTO and working...

17 January 2021 7,220 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View