How to avoid the melt-back etching when GaN grown on striped Si?

03 April 2016 6,563 1 View

How to get the RSM figure using XRD data?

09 October 2015 7,301 4 View

How do I avoid cracking when growing AlGaN on GaN?

when growing AlGaN on GaN template, cracking always happens. do you have any idea to reduce cracking? i am trying to use the voids inside the GaN template to relieve the strian, anybody has ideas...

08 September 2015 923 6 View

How to explain the anisotropic propery of XRD data in semi/non-polar GaN?

For semi/non-polar GaN grown on sapphire, we always found that at different azimuth angle, the on-axis XRD rocking curve FWHM is very different. Some paper mentioned that this kind of anisotropic...

05 June 2015 3,199 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Are there lab markers/pens resistant to Roti-Histol?

Hi, I'm looking for a pen/marker to write on the smooth, transparent (non-frosted) part of microscopy slides which does not get washed away by alcohols and most importantly Roti-Histol. I want to...

24 February 2021 9,902 5 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

I have a problem with kanamycin - why the kanamycin doesn't affect?

Hi everyone, I need to expression of GFP with pET28 plasmid in E. coli BL21(DE3) plysE. Transformed cells have kanamycin and chloramphenicol resistance. Normally, only transformed cells should...

22 February 2021 4,032 4 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View