What kind of interface is being constructed in the API and why the updation is as late as 12 hours ?

15 June 2020 0 2K Report

The data news or the " arogya setu " provides better instances in the case of the API designed as the update time is 12 hours. A prototype of real-time involvement should be carried out using DNS for direct link in the API interfaces.

Badges
Science topic

Similar topics
Correction

More Sumit Swain's questions See All

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

Can an airplane stay up in the the air without moving forward just like helicopter ?

How the lift and weight cancel each other perfectly for a helicopter to stay it motionless? Because its propeller do generate huge amount of lift due to air pressure plus a blend of air stream...

09 February 2021 3,990 14 View

For Carbon-emission free steelmaking by electrolysis with nonoxidizable electrode in EAF, what would be electrode material?

While CCS can be employed along with a conventional Carbon-efficient EAF steelmaking process (especially from iron ore) or even Hydrogen or hydrocarbon can bee passed through central electrode,...

30 January 2021 3,378 1 View

What are the factors on which exchange current density of an electrode depends, and how can they be predicted?

While surface roughness is an obvious factor, this is not what is exactly asked. Rather, periodic variation of exchange current density (of an electrode) with solution chemistry (of electrolyte)...

30 January 2021 4,886 5 View

What are the thermodynamic and kinetic similarities and differences among dendrite formation during solidification of metals, ceramics and polymers?

Basic dendrite formation of metallic alloys are explained by thermal and constitutional degree of supercooling and most-supercooled band of liquid somewhat ahead of solidification front that...

30 January 2021 8,450 2 View

Is it possible to economically reuse the heat content of water vapour that is generated during quenching of continuous casting of steel?

A huge amount of water is evaporated to cool down and solidify the liquid metal strands coming out of bottom of CCM mould. The steam contains significant latent and sensible heat energy, besides...

26 January 2021 3,446 4 View

Why it is not permissible to correct all 5 classical optical aberration (spherical, chromatic, coma, astigmatism, curvature of field) simultaneously?

When first order paraxial optics is expanded to third order optics (i.e. sin x~ x-x3/3! instead of sin x~x) , these 5 optical aberrations result in. What is the rigorous mathematical proof that,...

26 January 2021 8,666 4 View

Is it possible to prepare clay minerals by mixing pure oxides of required elements? What would be theoretical difficulties with it?

Practically this is not at all necessary. But theoretically, would hydrous/hydrothermal synthesis be enough (like mix 1 mole alumina gel and 4 mole silica gel and gently heat) or would it require...

26 January 2021 6,403 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How can Gamma Ray API units be converted to CPS (counts per second)?

Oil and gas companies run gamma ray tool and take readings in API units while Gamma ray is also noted in cps, so how these units can be converted into each other?

24 February 2021 7,545 2 View

What is the most prevalent drug related problem in the developed countries?

Detecting the drug related problems is an important step in the pharmaceutical care plan

21 February 2021 5,421 3 View

How to call both UMAT and UEL together in Abaqus?

I have a model with bulk material (matrix) and inclusions and cohesive interface elements between both. For the bulk material, I have implemented a UMAT and for the cohesive interface elements, I...

20 February 2021 1,286 2 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

XRPD Quantification - Building a calibration curve of drug excipient?

I am aiming to utilise XRPD to quantify a drug excipient within a drug product and have been having a little trouble building the calibration curve to allow for this quantification up until this...

10 February 2021 6,145 3 View

Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm??

Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm from the exposed surface in Abaqus... i am performing a coupled...

10 February 2021 4,656 2 View

Student writing his own Learning Outcomes - is this the way forward?

'Students just dont want to study; they are here to waste time!' I have heard this phrase many times; so are the students solely to be blamed? We will find many students who just dont seem to...

04 February 2021 8,546 22 View

In Abaqus, is it possible to remove elements which are too complex for meshing from a sequence obtained by getByBoundingBox() ?

Hello everyone, I'm trying to mesh a structure with complex partitions using mesh controls. When doing it on the user interface I'm first selecting all cells. In the following, I have to accept...

03 February 2021 8,198 1 View

I am working with crack propagation along with delamination using ABAQUS. Wether crack will start from a delaminated portion (cohesive crack) by XFEM?

I am modelling a SENB Beam with an interface. The interface is modelled with cohesive elements to permit delamination. The carck in the continumm is taken care by the XFEM. My doubt is the crack...

19 January 2021 4,827 1 View