What is the yield stress of Barium Strontium Titanate?

Vineeth Venugopal @Vineeth-Venugopal

24 March 2013 1 6K Report

If there is no data on BST, BT might also do. Is there a good hand book or resource to get these values?

Vineeth Venugopal

Thank you so much!

Badges
Science topic

More Vineeth Venugopal's questions See All

Can I know the information and treatment or control of Intervenning variables, Moderating Variables and Extraneous variables in Social Sciences?

Please share your knowledge or give your opinions or share any matterial with you regarding the same. Thank you all for your support in advance.

05 December 2023 6,969 2 View

Hello community, how to get the value of the real time load applied during load stepping (via time stepping) process in Ansys workbench?

While doing a structural analysis to check the plastic limit load of a component, the solution stops shortly before the end of the time step after successfully solving several substeps. I'd like...

09 November 2023 6,999 2 View

What is the best way to simulate a OWT tower and foundation system in ABAQUS?

I am trying to do numerical research on the Structural Dynamics of an offshore wind turbine tower along with the monopile foundation and SSI. I want to assess the behavior of this structural...

09 July 2023 6,641 0 View

How to model a random short fiber RVE in Ansys MAPDL?

Required for a project ASAP!!!

26 April 2023 6,725 1 View

How to calculate 95% CI for the effect size that was calculated using Mann Whitney U test?

I have calculated effect size for Mann Whitney U test. Now I need to calculate 95% CI for that effect size. How to go about it?

25 April 2023 9,981 4 View

What is the normal HOMA %B and HOMA- IR levels in normal healthy individuals?

Currently working on a project and it would be really useful if you could kindly help me with the normal HOMA- % B in normal healthy individuals and during the diagnosis of type 2 diabetes...

26 March 2023 7,486 1 View

Why ANSYS Explicit dynamics doesn't support fatigue tool?

Dear friends, I want to understand the fatigue behavior of the component under impact or shock load. To simulate the impact load I have chosen ANSYS explicit dynamics. But, there is no fatigue...

28 February 2023 3,433 5 View

Can you use RIPA buffer to extract membrane proteins from cells? if not whats the best way to prep lysates to detect membrane protein?

I have used RIPA buffer following the protocol listed on a Nature paper. But I have not been able to detect the protein of interest. Have tried three different sources for the antibody and also...

08 December 2022 5,255 2 View

Where might I find rating scales for anxiety/depression in South Asian languages?

I'd be grateful if anyone could direct me to where I might find rating scales for assessment of anxiety/depression in South Asian languages - such as Urdu/Punjabi/Bengali/etc.

27 December 2021 5,011 3 View

What treatment would be recommended for the management of anxiety and depression symptoms in patients with SSRI sensitivity?

I'd be grateful if anyone could direct me to evidence-based guidelines/recommendations on managing anxiety/depression in patients with SSRI sensitivity, i.e., patients who have difficulty...

30 October 2021 1,264 6 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

Wrong out put for gmx x2top?

Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...

24 July 2024 367 4 View

What binder would be the best choice to modify glassy carbon electrode with a 2D Material like Graphene or MXene?

I am trying to drop cast 2D Materials on Glassy Carbon Electrode for Cyclic voltametry and EIS purpose. What would be best binders to use?

23 July 2024 5,776 2 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View