What is the Tensile Strength value for Polypropylene plates of thickness 5 mm and width 50 mm welded by Friction Stir Welding?

More Venu Jaiganesh's questions See All

Can I use General Health Questionnaire (GHQ-12) to study psychological distress among flood affected individuals in 2018?

I would like to asses the psychological distress among August 2018 flood-affected individuals. Can I use GHQ-12 in 2020?. Because there is a time gap of 1 and half years after the floods, does it...

23 February 2020 9,731 3 View

Merging data is SPSS by variable?

I have two data sets A and B. Set A has 6000 cases but has interested variable V1. Set B has a variable V2. The cases are generic in set B (so cannot merge with Set A by case). I want to add V2...

31 January 2020 8,408 3 View

How far (Kms) that the Salt water intrusion takes place from the sea (Underground) towards the main land?

Suppose If I want to dig a well say near to the Arabian Coast (India), How far from Sea that I have to dig a well in order to avoid the salt water intrusion through coastal aquifers. I would like...

23 May 2019 2,859 1 View

Endothelium Derived Hyperpolarization Factors and significance?

I am interested to know if EDHF a primordial factor for relaxation? What are the physiological relevance and sources?Does EDHF observed in Conduit artery provides any significant impact in...

20 April 2016 7,710 14 View

Want to know best algorithm for Approximation algorithm and Distributed algorithm in Dominating set and Wireless Sensor Networks?

I want to know which algorithm is regularly used for Approximation algorithm and Distributed algorithm in Dominating set and Wireless Sensor Networks?

28 March 2016 5,044 1 View

Are soluble proteins active or inactive?

I am curious to know whether soluble proteins are active in circulation? or they become active after entering the extracellular space? I know it varies from protein to protein but would like to...

21 January 2016 7,774 3 View

How to check the micro and macro analysis report for welded joints ?

I tested but whether it is right or wrong I got the test reports from a testing lab.

27 March 2014 7,227 2 View

Sometimes for my PCR reaction I am getting a perfect desired single band and another time I am getting an extra faint band with desired band.

I am using a drosophila genome extracting a particular gene. I tried using fresh DNA, sterilized water and my negative control is perfectly alright. Each time i repeat my pcr the results varies;...

17 April 2012 2,026 2 View

In FM based passive radar how to Compressive sensing(CS) technique to improve range resolution, side lobe mitigation, target detection

Compressive Sensing is very popular technique to process sparse signal. most of the researchers applying CS technique for DVB-T/DAB or OFDM, GSM based passive radars whose bandwidth is small,...

01 January 1970 7,259 1 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Harpreet Singh Grewal

Can you frame your query more clearly. Becaseu as i can see that you might have done the tensile test on your specimen. You can easily analys your data and calculate it.

Venu Jaiganesh

yes i canducted the tensile test here iam attached the graphs can you conclude anything with this because the testing has been done in different lab.

I think you better get the raw data and plot them for better understanding as the scale bars in these plots has not been adjusted accordingly.