I'm running out of sheath fluid for my Fortessa and the vendor is also back-ordered. Can I make my own? Any tips to last me through the holidays?
Hello Debbie Jin
Please refer to the links below. They will be helpful.
https://expert.cheekyscientist.com/what-is-sheath-fluid/
https://immunology.ufl.edu/instrumentation/tips-and-tricks/sheath-fluid-and-sort-buffers/
Best.
Dear colleagues, I want to know the average analysis data of EPR effect on inflammatory tissue (acute lung inflammation/injury, ischemia/reperfusion, rheumatoid arthritis, and sepsis..) In...
22 December 2020 3,147 2 View
Chemical vapor deposition (CVD) was used to grow graphene on copper (Cu ) substrate, then the single layer graphene was transfered onto a PDMS substrate. I want to measure the bonding strength of...
17 October 2020 3,567 3 View
28 June 2020 7,614 3 View
Hello everyone Recently I wanted to purify several proteins by prokaryotic expression, I read some related literature and found that Mg is needed in the protein purification buffer. I am a little...
02 May 2020 931 3 View
I have data for a mental health study with a relatively small sample (N=80). I have been researching whether I can run a parametric analysis with my non-normally distributed data but am going...
22 April 2020 1,637 3 View
Hi all! I want to compare healthy vs cancer gene expression. I have three datasets available: Gtex, TARGET and tcga. All of these datasets are normalized to tpm units. I read about comparing...
29 March 2020 7,427 1 View
I have a free acid R-COOH and its salt R-COOM. Both are insoluble in water but soluble in methanol. When their methanol solutions are injected into a HPLC-PDA-MS system, are they going to have the...
06 March 2020 4,952 4 View
I am using the SDQ and Achenbach suite scales and at the point of cleaning data. I want to ensure that I have entered the correct measure for each of these items both in terms of methodological...
07 January 2020 9,992 3 View
Can anyone suggest where to find the data or any equations related to the salt solution vapor pressure at sub-zero temperature? Many thanks!
24 December 2019 7,741 2 View
When doing the systematic reviews, if you I confirmed a publication bias during meta-analysis, my questions is what to do next? I though to add discussion about the publication bias, but I want...
17 November 2019 5,634 4 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...
02 March 2021 1,999 5 View
during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...
01 March 2021 7,476 4 View
I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...
01 March 2021 6,985 3 View
Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...
01 March 2021 3,867 3 View
I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...
01 March 2021 8,668 3 View
How can one improve mesh skewness, orthogonality, aspect ratio?
28 February 2021 7,730 3 View
I want to do wettability analysis of hydrocarbon oil (octane)/rock/surfactant solution system. but to do the analysis first I have to make rock surface oil-wet. Since hydrocarbon oil does not have...
27 February 2021 5,383 3 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View
Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...
25 February 2021 9,602 4 View