The endothelial cells have more affinity to positively surface of polymer scaffold, I want to know why ECs were attached to that nanoparticles which I called.
Please help me.
Besides surface charge, nanomaterials has unique surface properties and surface energy.
tnx dear jia
may the electrospinnig charge the nanofibers surfaces? if yes, what charge?
just check with the zeta potential.. I have one paper and one more paper in our group
http://www.sciencedirect.com/science/article/pii/S1369703X14001454
http://pubs.acs.org/doi/abs/10.1021/ie303273s
Surface charge is a characteristic of materials which is strongly dependent on surface chemistry of particles or fibers and pH of colloid.
the only way to measuring surface charge is using zeta sizer, but you can use potentiostat or galvanostat regarding to measuring molecular charge.
hope this be helpful.
Tnx Mr Shaki and Singh
Dear Strum
Thanks alot...
we guess, we had uncompleted reaction between formalin and phenol or some changes are needed in process. and also we need to have final resin with 50% solid content and 200 cp in viscosity.
05 June 2017 8,907 0 View
I want to to analyze MWCNT and TiO2 into the nanofibers without utilizing TEM, please introduce me to another method.
31 December 2013 2,860 5 View
May the MWCNT lose their L/D after 20 min sonication?
11 December 2013 8,081 3 View
After half an hour of MWCNT in a PVA solution depositioning into needle and interrupt feeding of solution.
10 November 2013 8,807 3 View
I want to know how I can I solve laponite and PVA in water.
09 October 2013 7,115 1 View
In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...
01 March 2021 2,207 3 View
Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...
28 February 2021 7,882 2 View
I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...
28 February 2021 298 3 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View
I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...
23 February 2021 4,155 4 View
I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...
22 February 2021 5,324 3 View
Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...
16 February 2021 2,635 2 View
Hi! I am looking for some specific information in regards to the minimum amount of UV intensity required to begin the photo degradation process in polymers. I understand each polymer is...
15 February 2021 7,703 4 View
I had treat my XRD diffraction pattern by Highscore to calculate the crystallinity degree Xc and I have the formula but I dont no the 2Theta of Ac and Aa to calculate Xc. Is it like polymers...
10 February 2021 6,305 5 View
I am modeling CFRP laminated a concrete column in Abaqus And I need Elastic and plastic properties of CFRP
09 February 2021 4,930 5 View