After applying resole resin on a paper as a coating, we faced with formalin odor about a week after using. what should we do?

06 June 2017 0 9K Report

we guess, we had uncompleted reaction between formalin and phenol or some changes are needed in process.

and also we need to have final resin with 50% solid content and 200 cp in viscosity.

Badges
Science topic

More Soheyla Karimi's questions See All

What is the surface charge of PVA nanofibers, graphene and MWCNT, TiO2?

The endothelial cells have more affinity to positively surface of polymer scaffold, I want to know why ECs were attached to that nanoparticles which I called. Please help me.

07 August 2014 3,407 6 View

Does anyone know any methods for investigating nanocomposites except TEM?

I want to to analyze MWCNT and TiO2 into the nanofibers without utilizing TEM, please introduce me to another method.

31 December 2013 2,882 5 View

Does anyone know what is the sonication effect on MWCNT after about 20 min?

May the MWCNT lose their L/D after 20 min sonication?

11 December 2013 8,106 3 View

How to electrospin PVA+MWCNT solution without the depositioning of MWCNT into needle of a syringe?

After half an hour of MWCNT in a PVA solution depositioning into needle and interrupt feeding of solution.

10 November 2013 8,826 3 View

Is anyone familiar with the solving characteristics of laponite in distilled water before adding PVA to solution?

I want to know how I can I solve laponite and PVA in water.

09 October 2013 7,135 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

A positively charged and 10x his-tagged protein that doesn't bind to any chromatographic resin?

Hello everyone, I am currently working on a protein that is 10x his-tagged and positively charged (predicted pI=10.16). But when I tried to use Ni-NTA column to purify the protein, it's not...

24 July 2024 7,293 4 View

How to add viscosity into a hyperelastic material such as Mooney-Rivlin rubber in LS-DYNA?

Hi, I am working on a head FE model and want to try different material types on brain. I read some papers that use Mooney-Rivlin rubber model and wondering if i can add viscosity into it. Is it...

24 July 2024 5,908 0 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

Prevent sedimentation and maintain the suspension of powder particles in the resin ?

Hello, I am experiencing an issue with mixing micro powder with resin in a 3D printer. The problem is that sedimentation occurs after a short period (about half an hour to an hour). Could you...

23 July 2024 1,672 0 View