In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

No title

02 March 2021 932 1 View