What is the mechanical strength of flash in hot forging dies?

03 March 2015 0 6K Report

Someone knows which is the relation between the mechanical strength of flash in hot forging dies and the type of forging steel, the forging temperature, the internal pressure die, the flash shape and dimensions?

Badges
Science topic

More Daniel Martinez Krahmer's questions See All

Sheet steel laser cutting?

If you have a laser cutting machine that can cut a steel sheet up to 10 mm thick, is it possible to cut a 20 mm steel sheet in two consecutive passes? If the answer is yes or no, why?

09 October 2019 9,436 3 View

Lubrication regimen in pin on disk test?

I know that a way to establish the lubrication regime in a pin on disk test is by measure the resistance between the pin and the disc. Some papers say that if the resistance is of 2 ohm, the...

05 June 2019 7,949 3 View

How to create a mechanical engineering graphical abstract ?

Hi People. Here in RG there is a similar question but for works in biology. Some of you know if is there any software available to design mechanical engineering graphical abstracts ? Something...

31 December 2018 3,587 2 View

Warm forging of SAE 1045 steel?

Hi People. I need to know the temperture range for making warm forging of SAE 1045 steel.

31 December 2018 4,719 0 View

Hot forging dies made by SAE H13 tool steel?

Please. I need to know what level of hardness provide a equilibrated behaviour between wear resistance and toughness. Also, if a ionic nitriding treatment reduce the friction factor between the...

10 November 2018 6,622 1 View

Redes neuronales artificiales?

Esta pregunta es solo para los amigos y amigas de RG que hablan español. Les quiero preguntar si me pueden recomendar, al juicio de cada uno, cual es el mejor libro en ESPAÑOL para poder aprender...

09 October 2018 8,917 0 View

Turning of low carbon steel?

People. I need your colaboration. What value of hardness do you think is the minimal to not worsen the maquinability level of the steel? I work with steel of 0,1% C. I some of you have a paper, is...

08 September 2018 9,430 3 View

How do I assess ignition risk during magnesium turning?

Some people say that the risk is bigger when the chip particles size are 500 micrometers or minus? What is the reason of this size?

07 August 2018 7,725 0 View

Recrystallization temperature of one steel?

Please. I need information about the recrystallization temperature of SAE 1010 steel, and also the temperature range for warm forging.

05 June 2018 5,844 3 View

Grinding ball manufacturing by hot rolling process?

Hi People. Please, I need to know which is the best material to make the guideline plate in a hot rolling grinding ball machine. Here the is a link to see the...

02 March 2018 832 6 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

How to make the concentration measurements for the hydrogen absorption/desorption in the metal hydride?

Hello Everyone! I am trying to create a metal hydride system where I am trying to create a temperature control with the emphasis on measuring the concentration of the hydrogen with the hydrogen...

29 July 2024 7,577 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

How can biogenic synthesis techniques be applied to develop plants capable of extracting and processing heavy metals from contaminated soil, and wha?

Understand how to utilize biosynthesis to develop natural and sustainable solutions to address heavy metal pollution and improve environmental and agricultural conditions.

26 July 2024 1,469 1 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View