Any thoughts for a research topic in a master's level thesis regarding combination of Supply chain and entrepreneurship?

Hi, we are two master's students at JIBS and currently looking for inspiration and suggestions for a research topic that has a connection of both "supply chain" and "entrepreneurship". maybe...

18 November 2020 2,524 3 View

What types of stationary phases and solvent conditions are used for protein purity analysis via thin layer chromatography??

I have a protein labeled with a fluorescent dye (fluorescein) and I am hoping to get a quick measure of purity using TLC after dialysis. TLC is quick and easy so I am hoping to start there. What...

15 November 2020 7,319 3 View

Hi for every one I need the primer for ABO rs495828 ( ARMS or allele specific PCR)?

the primer for PCR ( ARMS or allele-specific ) for scientific research either from the studies or someone who has the ability to deisgn the primer for me as a required features above/ thank a lot...

20 September 2020 224 4 View

Some of the universities held the conferences based on virtual technique because of the pandemic?

What is the scientific sides to this conferences?

09 June 2020 8,047 1 View

Hello all, could any one help me to find the properties of parrafine wax that I need to model this type of wax in Abaqus?

If any one know how to model wax in Abaqus that's will be very helpful.

27 October 2018 8,165 2 View

How to calculate kWh in a PV solar concentrator?

Hi All, I got confused in finding the proper method to calculate the kWh(Energy) that can my solar concentrator produce in a certain location. I 've got the Peak Sun Hours (PSH) calculated which...

04 September 2018 2,270 2 View

What is the ROC curve analysis?

Currently, I am working on medical image processing. So What is the ROC curve analysiscan be use for the classifiers?

02 March 2018 2,082 4 View

What are major problems in medical image segmentation?

Currently, I am working on microscope image segmentation. Is the any recommended about major problems in medical image segmentation

26 November 2017 9,163 8 View

How can I model damage evolution in composite material under abaqus standard?

Hello everyone, I am modelling a CFRP under quasi-static load. My model consists of 8 plies, each ply has a thickness of 0.125mm and I am using a cohesive surface between the plies to find the...

13 July 2015 4,074 7 View

What is the epidemyology of small bowel cancer?

01 January 1970 2,772 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Any references about insects or animals that can damage or weathering of rock or fossil material?

Are there any references to insects or animals that can cause damage or weathering to the rock or fossil material? books or paper that would be nice. Thank you very much!

24 February 2021 6,805 3 View

Buckling analysis of a cylindrical shell in Ansys APDL?

In Ansys APDL, We are trying to validate our shell model for nonlinear buckling analysis considering the initial imperfection (as given by Ahmed et. al.) We have attached our results as attached....

13 February 2021 9,200 5 View

How can I get the moment on solid elements in Finite element modeling?

Unlike shell elements, solid elements have three degrees of freedom. So how can I get the values of moments after I run the model/analysis on ANSYS / ABAQUS ?

21 January 2021 258 3 View

What species (or genus even) of crab is this (bivalve using hermit type)?

Two weeks ago I found a peculiar crab in the intertidal zone in SW Florida. when found, the crab was not utilizing a shell. It was similar shaped to porcelain crabs found in our area, but with...

17 January 2021 1,620 4 View

What refrence values should i choose for calculating the Nusselt number and surface heat transfer cofficeint?

I executed simulation for a heat exchanger (shell and tube) . but i have a question that if i dont set the reference values and leave them as default values and as you know default temperature of...

10 January 2021 1,573 7 View

Is there any analytical model to asses impact of rigid projectile on monolithic deformable plate?

I am trying to select suitable element type (Solid or Shell) for impact analysis. I have tried with both solid and shell elements. The results are same for both element types up to certain impact...

08 January 2021 3,251 4 View

What is the different between plane182 and shell181 elements in ANSYS?

What is the difference between plane and shell elements in ANSYS? other than the fact that plane has 3 degrees of freedom and shell has 6 degrees of freedom?

28 December 2020 1,811 3 View

Does ANSYS consider the thickness of the shell181 element for the stress results?

Is the stress throughout the thickness of the shell element the same? I learned that transverse shear stresses are accounted for in SHELL181 but I also read that stresses in shells along the...

28 December 2020 4,515 4 View