What is the effect of low temperature performance between low carbon and high carbon steels?

More Pranav Shinde's questions See All

Why is stress-strain curve of austenitic stainless steel different from carbon steels?

Please see linked image

01 February 2017 4,843 0 View

Find residual stresses through XRD in formed tube?

I have a formed tube with reduction in diameter, i need to find residual stress through XRD. For sampling I can either cut a small section of hollow tube or make powder of it. If i turn my sample...

09 October 2016 626 8 View

How does the mechanical properties vary from extruded aluminium tube to pressure die casted aluminium tube?

Considering application for torsion only.

08 September 2016 2,201 9 View

In Ansys fatigue calculations how do you provide frequency of one cycle?

How does the calculations take into consideration effect of time.

08 September 2016 7,757 2 View

How to calculate theoritically work hardening induced stresses due to tube forming process?

Is it possible to get values in LS Dyna?

08 September 2016 6,445 5 View

Can we establish a relation between von mises, prinicpal and shear stresses?

For FEA calculatons

08 September 2016 1,431 1 View

Does curl of a function neccesarily needs to be constant?

What does curl of function physically represent?

07 August 2016 5,304 3 View

Improving residual stresses in DMLS/SLM AM components?

Using techniques like laser shock peening and particle shot peening, residual stresses at the surface can be taken care of. But how is it possible to cure internal residual stresses within core of...

05 June 2016 568 1 View

How are residual stresses in material compared with Grain size?

Macro residual stresses are considered to be larger than the grain size, how is this justified and understood.

04 May 2016 6,220 14 View

How can we plot stress strain curve for mild steel in ansys workbench?

Is it possible to plot non linear behavior of steel.

31 December 2015 2,778 2 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

Shivraj SINGH Kasana

My dear Shinde;

You will not find the data for low temperature two carbon steels AISI1035 and AISI1045, However you can determine the low temperature properties like T.S.,Y.S., %E,%R.A. and F.A.T.T.(Fracture appearance transition temperature) in cryoginic chambers with temperature ranging from ambient to -196 degree cel.Please refer ASTM A370 and discuss with me if any clearifications needed.As a guiding rule low carbon steel will behace better at low temperature in comparison to high carbon steel.

Shivraj Singh Kasana