Improving residual stresses in DMLS/SLM AM components?

06 June 2016 1 664 Report

Using techniques like laser shock peening and particle shot peening, residual stresses at the surface can be taken care of. But how is it possible to cure internal residual stresses within core of components?

Yunus Kayacan

I think, All peening method operates for getting compressive residual stresses, not removing.

Also You could check normalising anneals, If you need little amount of residual stress in the inner part.

Have a good work.

Badges
Science topic

More Pranav Shinde's questions See All

What is the effect of low temperature performance between low carbon and high carbon steels?

AISI 1035 vs AISI 1045 peeformance?

31 December 2017 6,363 3 View

Why is stress-strain curve of austenitic stainless steel different from carbon steels?

Please see linked image

01 February 2017 4,991 0 View

Find residual stresses through XRD in formed tube?

I have a formed tube with reduction in diameter, i need to find residual stress through XRD. For sampling I can either cut a small section of hollow tube or make powder of it. If i turn my sample...

09 October 2016 735 8 View

How does the mechanical properties vary from extruded aluminium tube to pressure die casted aluminium tube?

Considering application for torsion only.

08 September 2016 2,308 9 View

In Ansys fatigue calculations how do you provide frequency of one cycle?

How does the calculations take into consideration effect of time.

08 September 2016 8,091 2 View

How to calculate theoritically work hardening induced stresses due to tube forming process?

Is it possible to get values in LS Dyna?

08 September 2016 6,581 5 View

Can we establish a relation between von mises, prinicpal and shear stresses?

For FEA calculatons

08 September 2016 1,712 1 View

Does curl of a function neccesarily needs to be constant?

What does curl of function physically represent?

07 August 2016 5,423 3 View

How are residual stresses in material compared with Grain size?

Macro residual stresses are considered to be larger than the grain size, how is this justified and understood.

04 May 2016 6,504 14 View

How can we plot stress strain curve for mild steel in ansys workbench?

Is it possible to plot non linear behavior of steel.

31 December 2015 3,171 2 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Who of all the Global Scientific community will help me Prof. Dr. Yoshida make way for TPEOM, MEC ~EMC to return the atmospheric gases to the norma ?

TEP presentation caption (The Environmental Project) Re: Why should Washington’s DC, or any country government point of location think of as nowadays of as to being 'tomorrow as to come! if it...

03 August 2024 2,484 1 View

How to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field in Techplot?

Dear Researchers I need to know, how to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field data in Tecplot? Thank You

02 August 2024 3,615 1 View

What is the role of oxidative stress in toxin-induced carcinogenesis?

What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...

02 August 2024 3,174 1 View

Where can I find free research instruments for Nursing?

for eg. transition shock scale

01 August 2024 5,998 0 View

Does the delta function actually make sense to use on point particles?

The delta function seems produce logical contradictions when analyzed on a fundamental level. I would be curious if anyone else agrees.

31 July 2024 10,109 3 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View