What is the difference between Voigt fluid and Kelvin-Voigt fluid?

31 May 2024 1 2K Report

While reading literature I have observed both words "Voigt fluid" and "Kelvin-Voigt fluid", but I am not getting that both are same or different. Can I get clarification please?

Jamel Chahed

Read for Example: "Greco, Rita, and Giuseppe C. Marano. "Identification of parameters of Maxwell and Kelvin–Voigt generalized models for fluid viscous dampers." Journal of Vibration and Control 21.2 (2015): 260-274." Available on: Article The study of initial-boundary value problems for mathematica...

Badges
Science topic

More Sangamesh ..'s questions See All

What are the parameters we need to consider in order to reduce the Ackermann' steering error?

we are designing formula Car for SAE Supra Event, our aim is to reduce the Ackerman's steering error as much as possible and what are the necessary parameters we need to consider other than...

25 May 2015 6,205 3 View

Which of these tools is a suitable tool for Impact ballistic application modelling analysis: ANSYS, ABAQUS, LSDYNA????

Can you please suggest a modelling and analysis software?????

20 January 2015 1,826 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View