What is the difference between ferritic and austenitic nitrocarburized?

18 April 2020 0 8K Report

Which of them gives greater hardness and resistance to corrosion and wear?

Badges
Science method

More Victor Alcántara's questions See All

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to find a correlation between coordinates in a curvilinear coordinate system?

Hello. I have a skewed elliptical coordinate system (I use alternative elliptical coordinates). And I need to determine connections between coordinates in order to fetch a covariance matrix of...

28 February 2021 364 3 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

How to discriminate between Sentinel-2 Level-2A Product Discriminators?

According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...

21 February 2021 5,919 9 View

Are ZnS nanoparticles moisture sensitive?

Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...

17 February 2021 1,709 3 View

Can anyone suggest a software for running a plant tissue culture lab?

A software which can help to design the experiment, store data, update new data, set subculture reminders, barcoding etc. Like Invitrosoft.

17 February 2021 3,015 5 View

Is an encrypted dataset with Microsoft SEAL compatible with Cloudsim simulator??

Hello, I would like to do homomorphic encryption using Microsoft SEAL on my dataset and then use it as an input to the Cloudsim simulator to do clustering on. Is it possible and compatible with...

16 February 2021 3,915 1 View

Alternative to mediation analysis?

I am currently working on my dissertation and want to explore the role of competence as a mediator between the effect of colour of clothes on voting intention (focus on Western countries)....

21 February 2021 8,609 1 View

Why use both bead beating and enzymes (lysostaphin and lysozyme) for DNA extraction from sputum samples?

Hello, I have read in a few publications that to extract total DNA from sputum samples, both bead beating and enzymes are used to disrupt the cells. Bead beating is supposed to be efficient in...

18 February 2021 3,360 2 View

Has anyone done Archard Wear Simulation of GFRP Composite Plate in ANSYS with ACT extension or UDF?

I'm looking to do a sliding wear (plate-on-plate) simulation of GFRP composite plates with Archard Wear Model. Any hints or example steps are appreciated.

17 February 2021 1,447 2 View

How to make a site-Selective Electroless Nickel Plating?

I would like to plating Ni/Au on the selected area. Can anyone give me a suggestion? It is a bit like to make golden finger on PCB board. Instead with the PCB board, I use polyimide as my...

28 January 2021 8,330 1 View

Can I simulate Ferrite in HFSS?

I have a design with 2 dipoles working at different frequencies joined in one system and separated by Ferrite. I think, Ferrite was used to minimize the interference between 2 antennas as much as...

25 January 2021 5,918 3 View

How to use PVQ Psychometric Tool?

Hello, I'm doing a research about if psychometric tools can be translated into video games. My main major is video games. So I'm an absolute newbie with psychometric tools. I have chosen PVQ tool...

22 January 2021 5,992 2 View

Which Method of Statistical Analysis is best suit for making comparisons?

For the purpose of selecting the best one among the 4 design approaches, experimental video surveillance has taken. The dependent variable is the distance (meter) and the independent variables...

21 January 2021 4,936 7 View

How to measure the hardness for PLA & PHAs polymers?

Hello, I am a bit confused on whether to follow ASTM D785 (Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials) or ASTM D2240 (Standard Test Method for...

21 January 2021 7,487 4 View

How do I know the parameters for calculating the dislocation (edge and screw) density from XRD?

Especially the C12, C44, and Ai values for ferrite pearlite microstructure. Thanks

19 January 2021 9,035 5 View

How to get mesoporous cobalt ferrite thin film on Pt/Si substrate by electrodeposition method?

We want to deposit a thin film of mesoporous cobalt ferrite using a surfactant on Pt coated Si substrate by electrodeposition. What is the procedure for it? Does KLE polymer useful for this procedure?

10 January 2021 467 10 View