What is the design of Multiple Anti reflective coatings on silica nanoparticles on glass substrate to have zero reflectivity??

09 September 2017 0 10K Report

Silica nanoparticle with low refractive indices are are coated on class to minimize the reflectivity. I need best design for the these thin films coating. Please Answer this question and provide me some materials to study.

Badges
Science topic

More Kamran Alam's questions See All

How surface roughness and porosity of a surface helps in anti-reflection and self-cleaning phenomena of the surface?

I am working on anti-reflection and self-cleaning coating of solar PV module glass. How Roughness and porosity are related to each other in nano-particles coatings? and how these factors helps in...

06 July 2019 1,090 2 View

What is the effect of nanoporasity and roughness of the nanoparticles coating on transmittance of light ?

I want to increase porosity and roughness of the coating what will be its effect on light transmission and cleaning effect of solar PV glasss, or what are the limits

08 September 2018 1,745 2 View

How to calculate pore size from a TEM image ? If I know about particle size how to calculate pore size ?

Attached is a TEM surface image of Silica nanoparticles coating which is porous but how to calculate pore size. ??

08 September 2018 9,322 7 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Can chitosan alone can act as a reducing agent for Cu(0) nanoparticle sythesis?

[Synthesizing Cu nanoparticles without using chemical reductants]

01 March 2021 8,359 1 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View