What is the definition of "Overclosure" in Abaqus and how it relates with Pressure in contact analysis?

11 November 2018 0 5K Report

When editing contact property in the normal behavior tab, we can select the Pressure-Overclosure type that we desire. What is the definition of "Overclosure" in Abaqus and how it relates with Pressure in contact analysis?

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Samuel Hidajat's questions See All

Is there any circular plate deflection theory for hyperelastic material?

Hello, I am trying to find the frictional force between a polyurethane cleaning disk and the inside surface of a steel pipe. The disk is 105% bigger than the inner diameter of the pipe, so it will...

11 December 2019 5,720 1 View

How to Fix Frictional Contact Penetration Problem in Ansys?

Hello, I am trying to simulate contact between Polyurethane Disk Pig and the inside of a Steel Pipe in order to measure the frictional force experienced by the disk. The model that I use is...

10 November 2019 5,398 4 View

What is the minimum surface roughness required in order for PECVD coating to be deposited properly and have proper adhesion?

Hello, I am currently doing a project a surface preparation project on API L80 and P110 steel pipes to be coated with PECVD method. I am curious about the the minimum surface roughness required...

08 September 2019 6,508 4 View

Problem on load-displacement curve of compression test in Abaqus?

Hello, I am trying to simulate compression test on origami structure using Abaqus Static General and see the elastic-perfectly plastic behavior of the structure. Data extraction of displacement...

03 April 2019 1,377 3 View

How to adjust the position of faces in Abaqus?

As shown below, the middle face penetrates the left face and got away from the right face. I'm trying to make the faces continuous with each other (without penetration, only contact). Any ideas on...

31 December 2018 266 2 View

What is the difference between each hyperelastic models and their usage?

Currently I'm doing a project with hyperelastic material (TPE) and I'm trying to input the hyperelastic parameters in Abaqus. What is the difference between each hyperelastic models and their...

11 December 2018 5,260 1 View

Why surface to surface contact doesn't work in Abaqus?

Why does my structure still penetrate the plate? I have defined the plate as the master surface and my structure as the slave surface as attached in the picture below. The contact type is surface...

10 November 2018 4,720 7 View

Why do we need to put pressure magnitude if a tabular amplitude is already defined in Abaqus?

I am currently working on a project related to bending origami actuator utilizing air pressure. I am confused on why pressure magnitude needs to be defined if I already define the tabular...

10 November 2018 6,594 3 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View