What is the problem in attached file?

I have done ORR LSV (attached file) at different RPM (400-2000) in 0.1M KOH electrolyte (PH=13) using RDE. My teacher said that it is wrong due to limiting current density. Kindly give me your...

08 September 2019 1,662 2 View

How to do Particle Size Distribution of very small particles?

I used Image j but I didn't get correct result, is there another way to calculate particle size?

05 June 2019 8,862 3 View

How I can match simulated and own XRD pattern in Origin?

Hi, I have used American Mineralogist crystal database and downloaded .cif files and then used VESTA software to simulate XRD pattern and also have jcpdf number, I want to match with my own XRD...

04 May 2019 1,468 4 View

How can a beginner learn the analysis of X-ray photoelectron spectroscopy (XPS) by himself?

Is there any literature or trilaterals?

04 May 2019 3,309 6 View

Can anyone provide me JCPDS files?

Hi, everyone, I needed JCPDS files of Pt, Cu, PtCu & Cu3Pt, if anyone have then please share with me, I will be highly thankful. File numbers are as follows: PtCu = JCPDS 48-1549 Pt = JCPDS...

04 May 2019 1,856 4 View

What does it mean pass/fail in BET result?

I did BET for my catalyst (PtCu Nano particles) when I got result, I saw this error (given in attached figure), as BET Surface area is too low, what does "fail'' mean? is it incomplete analysis or...

03 April 2019 7,043 10 View

How can a beginner learn the analysis of XRD Powder method by himself?

Is there any literature or trilaterals?

01 February 2019 4,976 12 View

What is the standard electrode potential of Hg/HgO ?

01 February 2019 4,924 3 View

How to convert a potential collected with reference to Hg/HgO to Reversible Hydrogen Electrode?

I have collected a LSV data by taking Hg/HgO as the reference electrode. But I want to convert this one to RHE. Please suggest me the required conversion equation. 0.1M KOH was taken as the...

01 February 2019 6,730 4 View

Does anyone have the cif. file for ZIF-8 and MOF-74 ?

11 December 2018 8,137 0 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)*S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)*S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View