How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View

How to build .cks file (chemkin file) in ANSYS-Forte for hydrogen-diesel dual fuel?

Dear all, I'm trying to simulate the combustion of hydrogen diesel in dual fuel mode in ANSYS-Forte. I have kinetic reaction mechanisms file( .txt) but in order to build the .cks file in the...

28 December 2020 1,570 3 View

Could someone please help me in Parallelization of following UDF in Ansys fluent?

I was able set UDF for my dynamic mesh using following UDF. It works in serial mode. Now problem is that I want to speed up my solution, so parallelization is needed. I have gone through the user...

17 December 2020 420 4 View

How to integrate kinetic mechanisms for hydrogen diesel combustion for CFD analysis?

Dear all, I am writing my thesis on "CFD analysis on hydrogen assisted diesel engine". I am seeking help to construct the kinetic mechanisms for hydrogen diesel co-combustion. I managed to find...

03 November 2020 6,640 9 View

How to input engine load while performing CFD analysis on IC engines?

Hi all, I am currently writing my thesis on CFD analysis on dual-fuel hydrogen diesel engine to understand the behavior of emissions. At present I am using ANSYS Forte to conduct the CFD...

27 October 2020 3,369 3 View

How to add a third fuel-oxidizer stream in combustion model in ANSYS Fluent?

I am trying to develop a model for partially-premixed stratified combustion in ANSYS Fluent, which will have 3 separate streams with different equivalence ratios. I know that the 'secondary...

27 October 2020 5,644 1 View

Can we coat ceramic materials using flame spray or powder combustion spray?

Ceramic materials like Chromium oxide and Aluminium oxide have high melting point. The combustion flame can reach up to 3000 centigrade. However, The velocity of particle may not allow ceramic...

22 October 2020 2,963 5 View

How to calculate stoichiometric coefficient of coal devolatilization?

I am trying to model the coal gasification on fluidized bed. For this I need to define the chemical reaction of coal devolatilization in Fluent. Could you please help me how we can determine the...

21 October 2020 5,891 3 View

How can I track the decrease in initiation events of combustion?

Hello, I am interested in tracking the decrease in initiation events of different wildland fuel combustion. Apart from the experimental procedures, is there any simulation software that can help...

12 October 2020 7,905 1 View