What is the best way to derive the weak form for pde equation based modeling in COMSOL?

Hossein Daneshpajooh @Hossein_Daneshpajooh

04 April 2014 1 8K Report

I have read the Comsol documentation but i did not get it. I should use weak form pde to model my problem. the equation is attached in Fig. (equ). This is equation of piezoelectric movement.

Tij=0 in this case. All capital parameters are constant

Janderson Rocha Rodrigues

Hello Mrs. Daneshpajooh,

For coincidence, will be a webinar about it:

http://ecedha.org/ece-media/ece-webinars/comsol-webinar-4-17-14

Regards,

Badges
Science topic

More Hossein Daneshpajooh's questions See All

Is there any commercially available conductive acoustic impedance matching grease? and which ones have less attenuation/damping?

I need to use acoustic matching grease in between my copper electrode and PZT samples, however the usually used materials like silicon grease are not conductive and may interfere the electrical...

04 May 2018 1,380 1 View

How can I reduce/measure the response phase delay (time delay) between different sensory equipment output signals?

I want to measure the phase lag (time lag) between LDV vibrometer and other equipment such as voltage and current probes with accuracy of 1 degree (~nanoseconds). Unfortunately, the vibrometer has...

09 October 2016 5,212 5 View

How can I couple two parametric Solvers in comsol?

I need to use my first solver outputs as the second's solver inputs. I do it for non-parametric solvers using the dependent variable node options in solver configurations. But I need to run it...

04 May 2015 5,710 2 View

Why my model give me different answers, running with livelink-Comsol/Matlab, or With COMSOL alone?

When I change some parameters in my model using Matlab/Livelink it gave me different answers comparing to comsol alone. Here are the main codes: R1,R2,R3, k, etc were defined correctly! model =...

02 March 2015 1,177 2 View

How to enter material propertises of PZT materials in Comsol based on Voigt notation?

I am working in version 4.3a structural mechanics module with Piezoelectric Material Model. I am a little confused about which material properties are which in the matrix. The input field for the...

11 December 2013 7,556 1 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

Wrong out put for gmx x2top?

Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...

24 July 2024 367 4 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View

What binder would be the best choice to modify glassy carbon electrode with a 2D Material like Graphene or MXene?

I am trying to drop cast 2D Materials on Glassy Carbon Electrode for Cyclic voltametry and EIS purpose. What would be best binders to use?

23 July 2024 5,776 2 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View